67mm Lens Cap Strap Clip
Created today
Description
Pinching off a lens cap and immediately dropping it in the dirt is an avoidable mistake. This clip mounts directly to a camera strap to hold a 67mm pinch cap securely while the lens is in use, keeping it out of your pockets and off the ground.
- Strap slot: 42mm wide with a 3.2mm clearance and a diagonal slip-channel, letting it twist onto the webbing without unthreading the strap.
- Cap receiver: 67.5mm internal groove catches the cap's pinch prongs, with an angled lip to lock them in place.
- Tether loop: 6mm bore on the side to run a backup paracord lanyard.
- Print orientation: Internal overhangs are angled to print support-free when placed face-up on the plate.
Images
More like this
Explore more in Automotive, RC & Hobby →
Double Seatbelt Buckle Holder, Backseat
Two seatbelt buckles flop around and fall into the seat gap, so this holder stands both upright side by side in the backseat of a Toyota Sienta. Each 33 x 53 mm pocket goes straight through the base, so the buckle and webbing pass through with nothing blocking the bottom. Pocket size: 33 x 53 mm each, sized for a 31 x 51 mm buckle Sleeve height: 28 mm above a 6 mm base Overall footprint: 130 x 64 mm Centre screw hole: 4.5 mm Print flat on the base, no supports needed
Aura — Automotive Ring Emblem
A flat-backed, print-ready representation of the classic four-ring automotive logo. Designed to sit flush on the build plate for an easy print. Dimensions Overall Width: 124 mm Ring Outer Diameter: 40 mm Thickness: 4 mm Print Notes Prints directly on the bed with no supports required. The intersection points are fully merged to ensure the entire emblem prints as a single solid, structurally sound piece.
NAJMA
A compact, single-piece delivery truck chassis designed as Part 1 of a commemorative desk model. Engineered to print in place with zero assembly required for the base. Integrated Wheels: Solid cylinders fused into the chassis base for a robust, no-moving-parts foundation. Rear Platform: Provides a flat bed with two precisely placed alignment pins to locate a custom cargo box. Commemorative Markings: Features embossed text on the cabin roof celebrating the occasion. Built to be fully printable without supports, keeping the underside flat and stable.
Duo Gear — 30T and 15T Spur Pair
Duo is a matched pair of spur gears at a 2:1 ratio: a 30-tooth gear measuring 90 mm across the tips and a 15-tooth partner, both 10 mm thick. Tooth size is shared, so they mesh directly and are laid out at the correct centre distance. Features 30-tooth gear: 90 mm outer diameter, 10 mm bore 15-tooth gear: same tooth pitch, 8 mm bore Both 10 mm high, flat on the bed Pre-positioned in mesh Print notes Print flat, no supports. Adjust bores to fit your shafts.
Seatbelt Buckle Holder with Snap Clips
A twin seatbelt buckle holder with two separate snap clips. Each clip bridges the top of a pocket and clicks into grooves on the sleeve, so the buckle can't tip out. Remix hooks Bar width (8 mm): widen it for a firmer hold, or narrow it for easier buckle removal. Groove height (18 mm up the sleeve): move it to change how far the clip sits above the pocket. Barb depth (about 1 mm): increase it for a stronger snap, or reduce it if the arms feel stiff in your filament. Arm thickness (2.2 mm): thinner flexes more, thicker holds more. Pairs with: the original 33 x 53 mm pockets, 28 mm sleeves, and 130 x 64 mm footprint, all unchanged. Print the clips flat as laid out, with the bar on the bed. PETG flexes better than PLA for the arms.
Passat B6 Console Cup Holder 1.2v
A drop-in dual cup holder insert designed to fit the console space next to the handbrake in a 2006 Volkswagen Passat B6. The wedge-shaped body maintains a flush, horizontal top surface while following the sloped floor of the compartment underneath. Fitment: 180mm x 105mm footprint, tapering from 90mm down to 55mm in height. Capacity: Two 75mm diameter slots. The forward slot runs 75mm deep, and the rear slot sits 60mm deep to accommodate the console's slope. Features: Flared top lips for easy alignment, internal bottom fillets, and 5mm center drainage holes to handle condensation. Tolerances: Generous minimum wall and floor thicknesses (≥4mm throughout) ensure structural rigidity without requiring internal supports.