8.5mm Rod Square Drop-On Sleeve
Created 1 months ago
Remixed 3 times
Description
Square profile sleeve that slips onto a toilet roll holder rod to increase rolling friction, deterring toddlers from unspooling the paper.
- Fitment: 8.5mm diameter holder rods
- Outer Profile: 25x25mm square, 90mm tall
- Installation: Direct drop-on over the existing rod
- Note: Make sure to check your holder's rod diameter before printing. Prints upright without supports; PETG is recommended for durability.
Images
More like this
Explore more in Home & Fixtures →
4-Way Water Manifold
A compact, print-in-place water manifold built for automated plant irrigation systems. It splits a single main feed into four independent channels with smooth internal transitions to minimize flow restriction. Inlet: Single center-mounted fitting sized for 8mm ID hose. Outlets: Four equally-spaced fittings sized for 5mm ID hose. Barbs: Dual retaining ridges on all connections to prevent slip-offs under pressure. Internal Channels: Fully hollowed 7mm common chamber with spherical transitions to eliminate dead zones and sharp fluid corners.
4-Way Barb Manifold
Hoses slipping off a plain tube is a guaranteed flood. This 4-way manifold uses aggressive, precisely sized barbs to bite into soft tubing, routing one 8mm inlet into four 5mm outlets. Critical Fit Inlet: 8.2mm main shaft, 10mm max OD on three barbs. Outlets: 5.2mm main shaft, 6.7mm max OD on two barbs each. Flow: Internal bores are necked down to 3mm on the branches to preserve wall strength, expanding to a 16mm central chamber. Print it base-down. The horizontal barbs are short enough to bridge without supports if your part cooling is dialled in.
Eccentric Duct Adapter 125mm
A robust, high-flow duct adapter designed to transition a standard 125 mm round bathroom exhaust duct into a low-profile 220 × 90 mm rectangular flat channel. The design features a pronounced vertical offset to navigate tight ceiling or wall spaces without compromising airflow. What it's for This part connects two dissimilar ducting systems. It is strictly female-to-female, intended to slip over an existing 125 mm round male pipe on one end and accept a 220 × 90 mm flat duct on the other. The 72.5 mm vertical offset is specifically tailored to align the flat duct closely to a wall or ceiling plane while maintaining the round pipe's original centerline. Dimensions Round Socket: 126.5 mm inner diameter, 30 mm deep (includes a 1.5 mm entry chamfer for easier fitting). Flat Socket: 222 × 92 mm internal dimensions with 5 mm corner radii, 30 mm deep. Overall Dimensions: 220 mm total length, maintaining a continuous 2.4 mm wall thickness. Offset: Centerline shifts vertically by exactly 72.5 mm over a smooth 160 mm internal transition. Print notes Print this model standing upright on the round flat face. No supports should be necessary for the interior loft, as the transition angle is steady and fully convex. PETG or ABS is highly recommended over PLA for HVAC applications, as the exhaust air and environmental moisture can deform standard PLA over time. Ensure your slicing profile is set to completely fill the 2.4 mm walls (usually 3 perimeters depending on nozzle size) to keep the assembly watertight and structurally sound.
Eccentric Duct Adapter
An FDM-optimized structural adapter for mating a 100 mm circular duct to a 200 × 60 mm flat rectangular duct. Designed entirely through lofted profiles, the core internal geometry preserves precise clearance offsets before applying a constant outward shell. Continuous S-curve loft: Matches horizontal slopes at both sockets to eliminate turbulence edges. Built-in offset: 25 mm vertical eccentricity pushes the rectangular trunk higher than the round inlet axis while maintaining horizontal symmetry. Constant wall: Outward geometry maintains a uniform 2.4 mm thickness down the full 220 mm length of the part. Integrated chamfer: A 1.2 mm guide chamfer at the circular entry eases assembly of tight-fitting duct sections.
Compact Offset Duct Adapter
A parametric, FDM-printable ventilation duct adapter connecting a nominal Ø100 mm round duct to a 200 × 60 mm rectangular duct. Round Inlet: Ø101 mm internal diameter, 30 mm deep Rectangular Outlet: 201 × 61 mm internal, 30 mm deep Offset: 25 mm vertical centerline shift Wall Thickness: 2.4 mm (constant, pushed outward) Total Length: 210 mm (150 mm transition) Both ends are female sockets designed for a slip fit over existing plastic ducting. The loft provides a smooth internal airflow path with no steps or constrictions.
Deep Trough — Single Feeder
A deep, single-volume wire cage feeder. This updated design drops the middle divider and front perch to maximize internal volume. Perfect for dispensing large amounts of dry feed or hay. Dimensions Width: 3.5 inches (89 mm) Depth: 5 inches (127 mm) Height: 3 inches (76 mm) Features Heavy-duty S-hooks integrated into the rear wall Rounded internal corners for easy cleaning Thicker base (2mm) for durability