Created 1 months ago
Description
The torso had no base and tipped over the second a cable was bumped. I machined this pair of modular legs to give it a stance. They bolt directly to the 150mm underside spacing of the AuraZex frame, bearing the weight on overlapping 12.5mm pin joints instead of fragile ball-sockets.
Images
A wall-mounted holder that keeps a 3-ton jack stand and its handle off the garage floor and within reach. The flat vertical back plate carries a U-shaped cradle with a 28 mm bar seat at 65 mm up, the vertical middle of the 130 mm plate. The cradle is open at the top so the bar drops in and lifts out, and open through the middle with a 10 mm wall at each end. The front wall is a 13 mm lip that catches the bar. The cradle walls are rounded at 7 mm on every edge except the one against the back plate, and the inner floor is a 28 mm half-cylinder trough so a round bar lies in it without rocking. The holder prints as one piece. A compact gusset supports the cradle under its full 100 mm width, so the end walls sit flush on it instead of overhanging. Its corners carry the same 7 mm radius, and its underside is an S-curve that leaves the back plate low down, sweeps out, and runs straight up the front of the cradle, meeting both surfaces tangentially so there is no crease where it joins. Keep it around this size; trimming it further leaves little support for a loaded stand. The handle hangs from cuts in the holder rather than being threaded in from the front. The front wall has a 28 mm slit set to the right, centered 24 mm right of centre, open at the top and stopping 12 mm short of the outer edge so the right end wall stays full. The left end wall carries a matching 28 mm U-notch open at the top. The front slit and left notch share the trough floor, bottoming at 51 mm, so a 28 mm handle slides from the trough into them without a step and hangs below. The cradle walls are 55 mm tall and top out at 95 mm, leaving about 16 mm of wall above a 28 mm handle resting at 65 mm. Overall: 100 mm wide, 130 mm tall, 57 mm deep Cradle: U-shaped, 28 mm bar seat at 65 mm up, open top, open through the middle, 10 mm end walls Bar opening: about 80 mm between end walls Front lip: 13 mm thick Handle cuts: 28 mm front slit set right of centre, open at the top and 12 mm inboard of the outer edge; 28 mm U-notch in the left end wall open at the top Floor: trough floor bottoms at 51 mm with the front slit and left notch Cradle walls: 55 mm tall, top at 95 mm, 7 mm rounded edges Gusset: full cradle width, 7 mm rounded corners, S-curve underside tangent to the plate and cradle front Mounting: countersunk screw holes above and below the cradle; use 5 mm or larger screws into a stud or suitable anchor Material: grey PETG; chamfered edges Check that the stand's bar fits the 28 mm seat and the 80 mm opening, and that the handle fits the 28 mm cuts before printing; widen any of them if the real parts are larger.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
Un tablero de estilo muscle car a escala grande: 127 mm de diámetro exterior, con la esfera estriada, el dial negro de números grandes y una aguja fina de punta afilada que evocan los tacómetros AutoMeter de los tableros deportivos. La escala barre de 0 a 9.000 RPM en 180° —de las 6 a las 12 en sentido horario— y la zona roja arranca en 8.000 RPM. Detrás del dial va un servo SG90, así que la aguja se mueve de verdad, y el conjunto no lleva carcasa trasera. El dial mide 113 mm y deja 109 mm de ventana visible: números, marcas y zona roja escalan con el aro para que la aguja llegue a las marcas. El conjunto se imprime en siete piezas separadas y sin soportes: Aro frontal: 127 mm de diámetro, labio de 2 mm, estrías exteriores y cuatro agujeros para tornillos M3. Lleva una llave de orientación para el dial y dos agujeros piloto a las 12, a ±6 mm del centro, para la luz flash de corte de RPM. Dial: disco de 113 mm con los números 0–9 y los textos «RPM» y «x1000» pasantes de lado a lado —con puentes finos de 0,8 mm que sostienen las islas interiores—, marcas cada 500 RPM y zona roja en relieve. El agujero central es de 10 mm más 0,3 mm de juego de encastre. Aguja: perfil fino de aguja real, con puntero de 50 mm que se angosta desde 1,2 mm hasta unos 0,6 mm en la punta y una cola de contrapeso corta; el cubo central es de 10 mm para dejar el dial despejado. Se monta en el brazo del servo recortado a 12 mm de radio y se fija solo con el tornillo central de 3,2 mm, sin pasador. Soporte servo: placa de 4 mm con ventana para el SG90, dos agujeros piloto para la brida, muesca de llave y ventana de 12 × 12 mm para el cable del servo. Se fija al aro con cuatro tornillos M3 y recibe la caja de ESP32 con dos tornillos M3 desde adelante, con los agujeros a ±29 mm. La ventana del servo mantiene las medidas compactas del SG90. Caja ESP32: pieza aparte de 31 × 65 × 16 mm para una placa de 30 pines de unos 51 × 26 mm, con ranura para el USB, dos rieles internos que sostienen la placa y salida de cable hacia el soporte; se adosa al soporte del servo y queda por detrás. Caja de LEDs: cilindro de 41 mm de diámetro y 14,8 mm de alto, con paredes y fondo de 2 mm y cámara abierta hacia el frente. Va a las 12, con el borde curvado apoyado en el aro, y se fija con dos tornillos M3 horizontales a ±6 mm del centro; la salida del cable de la tira LED está en la pared trasera. Quedan unos 37 mm libres en el interior, suficientes para un LED o un tramo corto de tira. Tapa difusora: disco de 41 mm con solo 1,2 mm de piel, con un anillo guía que entra con 0,3 mm de juego. Es fina para que pase la luz y se imprime con la cara exterior hacia abajo; puede imprimirse en el color del flash —rojo, azul o blanco— en PLA translúcido o natural. Notas de armado y acabado: Los números pasantes dejan pasar la luz de atrás: se puede colocar un filtro de otro color detrás del dial y cambiar el tono de la iluminación. Los puentes se ven como una línea fina en medio de cada número: un puente vertical en el 0 y el 8, uno horizontal en el 4, el 6 y el 9, y otro horizontal sosteniendo la R, la P y los ceros de «RPM x1000». Es lo normal en un estilo stencil. El centro de 10 mm deja paredes de unos 0,9 mm en el cubo de la aguja; conviene imprimir esa zona con 100 % de relleno. Las marcas y la zona roja van en relieve en el mismo archivo que el disco: para cambiar su color hay que pausar la impresión en el cambio de capa. La tira LED no tiene soporte interno: se pega con su adhesivo en la pared interior de la caja de LEDs. Al montar, alineá el brazo del servo en 0° apuntando a las 6 y comprobá la altura del brazo sobre la brida en tu SG90 antes de cerrar el conjunto.
BeamWedge is a shallow mounting wedge for a motorcycle number-plate lamp. Its 15° face tilts the lamp down toward the plate instead of into the eyes of riders behind, while the 53 mm × 13 mm face matches the lamp body and keeps the profile compact. A pair of screw holes and a central cable opening let the lamp sit cleanly on a number-plate holder, and the 6.5 mm depth with a 3 mm thin edge keeps the wedge unobtrusive. All four corners are rounded at 3 mm radius, so no sharp points sit against the holder or the lamp body. Fit and features 15° downward tilt for aiming the lamp at the plate 53 mm wide and 13 mm tall to match the lamp body Two 5 mm screw holes at 37 mm centres 10 mm central cable hole 6.5 mm deep body with a 3 mm thin edge 3 mm rounded corners on all four points Print notes The 10 mm cable hole leaves roughly 1.5 mm of material above and below it across the wedge's 13 mm height. That is thin but printable — run extra perimeters so the narrow bands around the hole hold up. Before printing Check the 37 mm screw spacing and the 10 mm cable opening against your lamp before printing.
Straight and curved RC track pieces sized to fit a 250 x 250 mm print bed, using the same 90 mm wide track and bulb-and-socket latch as the rest of the set. What it fits Built for printers with a 250 x 250 mm bed or larger. Mates with the existing 90 mm wide pieces (80 mm clear lane, 5 mm rails) through the same latch with 1 mm clearance. Pieces Straights: 50 mm and 150 mm (the 200 mm straight also fits). 180° hairpin at 70 mm centreline radius, about 230 mm wide. 30° at 250 mm radius, 45° at 200 mm, 60° at 150 mm, 90° at 120 mm. Check before printing The footprint of each piece is measured from the model, but measure your bed's usable area, since brims and clips reduce it. Does not fit The earlier 180° hairpin at 100 mm radius, the main junction (about 440 mm) and the multi-way junctions are larger than a 250 mm bed. The latches have not been test-fitted.
A half-relief take on a Victorian terraced house in OO gauge: brick front with quoins, mitred corners and a roof that pitches back at 45° from the eaves, like the shop-front buildings that sit flat against a layout backscene. The side walls rise in a 45° slope to meet the roof, and the two tiled roof panels are sized to overhang the front and both sides. Brick front with separate window and door inserts Two mirrored side walls, 15 mm deep, with sloped tops Floor piece spanning between the sides Two tile-pattern roof panels, 36 × 25 mm each 45° mitred corner joins