Clam Coffee Stencil
Created 5 months ago
Description
A flat stencil plate designed to rest perfectly over a coffee mug, featuring a scalloped clam silhouette cut out of the center and a small handle for easy lifting. Ideal for dusting cocoa powder onto coffee foam.
Photos
Technical views
More like this
Explore more in Kitchen & Bathroom →
Toy Story Sky Cloud Cookie Cutter
A cookie cutter echoing the wallpaper clouds from Andy's room: a big bump on the upper left, smaller puffs along the top and a long flat base. The centre is open so dough passes straight through. 15 mm tall wall, about 1.2 mm thick, thin clean cutting edge on the flat bottom Widened rim at the top for pressing by hand About 100 mm wide, prints flat with no supports
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Antalya Kebap Untersetzer 3.0
Runder Getränkeuntersetzer im Kebap-Stand-Look: Die Schrift ANTALYA KEBAP II steht 1 mm erhaben auf einer glatten Fläche, umgeben von einem hohen Rand, der Kondenswasser und Verschüttetes im Zaum hält. Durchmesser 100 mm, Boden 5 mm stark Umlaufender Rand bis 6 mm Höhe Schrift 1 mm erhaben, Bebas Neue Die Schrift endet auf Randhöhe, daher bleibt oben alles bündig
8.5 Inch Tall Round Steamer Basket with Lid
A round steamer basket, 216 mm (8.5 in) in outer diameter and 70 mm tall, with a separate conical lid. The floor is slotted for steam flow, and raised bands on the wall suggest bamboo. Basket: 216 mm OD, 70 mm tall, 5 mm floor, 5 mm wall Floor: radial steam slots in three rings Lid: conical, with a round knob, fits over the rim Bands: three raised rings, surface detail only Print: two separate pieces, lid printed flat side down
140mm Striped Cookie Stencil
A flat, 1mm-thick stencil designed for decorating cookies and baked goods with horizontal stripes. The pattern features alternating 5mm cutouts and solid bands, enclosed by a rigid 10mm perimeter. A tab extends from the top edge for handling and includes a 6mm hole for hanging storage. Specifications Overall Dimensions: 140 × 140 mm (5.5 × 5.5 in) frame. Pattern Area: 120 × 115 mm. Stripe Width: 5 mm gaps spaced by 5 mm solid dividers. Thickness: 1.0 mm (ideal for 5 layers at 0.2 mm layer height). Storage: 40 mm wide top tab with a 6 mm hanging hole.
Sink Caddy With Drain Slots
Sponges and brushes left in a flat tray sit in a puddle and go sour. This sink caddy lifts them on ribs over a slotted floor so water runs out, and a separate tall holder takes a brush upright. Key numbers Tray: 200 x 110 x 45 mm, 2.4 mm walls Floor: 2.5 mm with 9 drain slots, plus 4 mm ribs to keep items off the surface Front notch: 60 mm wide, lets water pour off the front edge Brush socket: 48 mm square, inner opening 44 mm Removable holder: 40 x 40 x 100 mm with side slots for drainage; 2 mm clearance in the socket Printing Print the tray flat, no supports Print the holder upright 0.2 mm layers, PETG suggested for wet use