ClipBase — VW Door Mount
Created today
Description
A direct replacement mount for a broken VW Golf 6 door panel clip (6Q0 868 243). Designed to be printed in a weldable polymer (like PP) and permanently reattached to the interior door panel using a plastic welder or soldering iron.
Features
- Weld-Ready Base: Completely flat 32x25 mm bottom footprint maximizes the surface area for a strong perimeter weld.
- Tapered Insertion: V-shaped entry path allows the door clip to self-center during installation, ending in a secure 4 mm snap-fit neck.
- D-Shaped Profile: Rounded rear geometry eliminates sharp corners that could catch during the welding process, while saving material.
- Precision Cavity: Two-tier internal structure correctly houses both the 22 mm clip head and the 8 mm shaft without play.
Images
More like this
Explore more in Automotive, RC & Hobby →
Lego piece for wagon door runner with thinner teeth bit slightly smaller
Wagon door runner to replace 3 off 15208 bricks Version with slightly too large slope
AeroFit — Micro Motor Mount
A lightweight, minimalist motor mount designed to attach micro brushless motors to a standard 3.0mm carbon fiber boom. It prints flat on the bed with no supports required, making it an extremely quick and clean print. Features Carbon Boom Sleeve: Snug 3.0mm inner diameter with a flex slit, allowing it to clamp securely to standard RC plane tail booms. Motor Interface: 9x9mm hole pattern sized for M2 screws, standard for 11xx series micro motors. Lightweight Build: Thin 1.2mm walls keep weight to an absolute minimum while the conical transition fillet maintains structural rigidity. Print Notes Print upright (motor plate flat on the bed). No supports needed. PLA or PETG recommended for stiffness.
0.355 to 0.370 Golf Ferrule
Custom transition ferrule designed to mate golf shafts with an adapting taper. Before printing, verify your shaft tip standard. This part spans from a 0.355-inch taper dimension to a 0.370-inch parallel dimension. Critical Measurements: Inner Bore (Bottom): 9.0 mm (0.355") Inner Bore (Top): 9.4 mm (0.370") Outer Diameter: 13.5 mm (0.530") constant Length: 22.0 mm (0.875") Does not fit standard parallel-only 0.370" shafts at the base without binding.
Kid-Sized Palm Repulsor
A scaled-down version of the standard palm repulsor, proportioned specifically for a child's hand. Design Notes Overall width is roughly 57 mm to sit comfortably flat across a smaller palm. The side mounting slots are sized to accept a standard 1/2-inch elastic strap. Printed as three separate pieces to allow for distinct colours without painting.
Custom 16T Mod 0.5 Gear
What it's for A custom 16-tooth spur gear designed for tight tolerances and specific meshing requirements. Built with a modified pressure angle for a sharper tooth profile, and zero standard clearance to strictly match the requested root and outer diameters. Dimensions Outer Diameter: 9.00 mm Root Diameter: 7.00 mm Bore Diameter: 1.55 mm Thickness: 2.00 mm Module: 0.5 (with 28° pressure angle) Print notes Given the small 1.55 mm bore and fine module 0.5 teeth, a resin printer or an FDM machine with a 0.2 mm nozzle and highly calibrated flow is recommended. If printing on standard 0.4 mm FDM, horizontal expansion (XY compensation) may be needed to keep the bore true to size.
D-Shaft to Hex Motor Adapter
A rigid drive adapter connecting a standard D-shaft motor to a hexagonal RC wheel hub. The base features a keyed socket to prevent slip under torque, while the driven end seats into the tire's existing recess. Overall Length: 25 mm Motor Socket: 6 mm diameter with a 3 mm flat profile, 10 mm depth Wheel Drive: 5.2 mm flat-to-flat hexagonal peg, 10 mm length Base Diameter: 12 mm for structural wall thickness around the socket