CourtGuard — Vented Finger Splints
Created 14 days ago
Remixed once
Description
Designed to quickly immobilise jammed or sprained fingers, CourtGuard splints provide rigid support without trapping moisture. Ideal for handling the inevitable basketball court impacts, the half-cylinder trough design features a rounded capsule geometry that sits comfortably against the skin without digging in. A dorsal ridge of vent holes keeps the finger cool during recovery, while integrated side notches securely anchor standard Velcro straps to keep the splint exactly where it belongs.
Sizes Included
- Small (Pinky): 55mm length, 15mm inner diameter, 4 vent holes.
- Medium: 65mm length, 18mm inner diameter, 5 vent holes.
- Large: 75mm length, 21mm inner diameter, 6 vent holes.
Print Notes
All three sizes are designed to print-in-place in their current flat orientation, requiring absolutely no supports. A rigid material like PETG or standard PLA is recommended for maximum immobilization.
Images
More like this
Explore more in Keychains & EDC →
Football Keycap Topper
A custom Cherry MX-compatible mechanical keycap featuring a gently domed top and recessed seams, channeling the look of a classic basketball. Built from the ground up to respect a precise 17.25mm footprint, it trades the standard typing dish for a smooth, tactile convex surface. Court-Ready Specs Switch Profile: Deep Cherry MX compatible stem with a flared entrance for an easy press-fit. Surface Feel: A smooth domed top intersected by 0.6mm-deep recessed channels tracing the iconic hoops cross-and-arc pattern. Dimensions: Exact 17.246 mm square footprint at the base, tapering cleanly up to the rim. Printability: Designed fully manifold with built-in internal bracing ribs. The bottom cross interface is lightly chamfered to combat elephant's foot and ensure tight tolerances straight off the bed.
M22 Threaded Kettlebell Stash
A two-piece threaded kettlebell stash keychain. The main body has been hollowed out to maximize internal storage, then split squarely at the equator with a sturdy 2mm-pitch thread holding the halves together. Both halves print exactly as oriented — the base sits flat on its machined underside, and the top half prints directly on its equator ring. Fitment Notes Thread Clearance: Engineered with a 0.5mm radial offset on the internal thread. Check your flow rate if the halves bind on the first turn. Split Ring: The arch remains standardized for a 1.5mm wire gauge ring. Internal Volume: The cavity is approximately 20mm wide and 19mm deep when closed. Fits standard folded emergency bills or small hardware.
Captive-Pea Emergency Keychain Whistle
A 50mm print-in-place emergency whistle built around a 12mm spherical resonating chamber. It features a tapered mouthpiece and an integrated 7mm captive pea that creates a high-decibel warble, all packed into a low-profile keychain block. Remix Hooks & Constraints Chamber Geometry: The fundamental tone is dictated by the 12mm sphere. Expanding this chamber lowers the pitch, while shrinking it creates a sharper, higher shriek. Captive Pea: The 7mm pea prints with a 0.2mm floor gap. This clearance is just tight enough to prevent the sphere from tearing off the build plate, but weak enough to break free with a pen tip. Windway & Fipple: The air channel is fixed at 1.5mm high to compress the airstream before it hits the 45-degree splitting edge. Changing the fipple angle will dramatically alter the sound quality. Mounting Loop: The 5mm bore at the rear fits standard split rings and 550 paracord. If scaling the model for a heavier carabiner, reinforce the tail block first.
Chunky Modern Type Keychain
A solid, pocket-sized keychain featuring a custom typographic design. The base perfectly contours the bold lettering, creating a clean and modern silhouette that feels sturdy in hand. Pocket-Friendly Size: Scaled down to slide easily into a pocket without snagging. Sturdy Build: A solid 5 mm base prevents flexing, with 2 mm raised lettering that holds up to daily wear. Ready to Mount: Features a fully through 5 mm keyring hole to accommodate standard rings or small carabiners.
Embossed Corporate Logo Keychain
A minimalist, single-piece keychain blank featuring raised corporate typography. The body uses a flat-bottomed pill geometry to print seamlessly on an FDM bed without supports, while the integrated mounting hole ensures the outer perimeter remains completely uninterrupted. Print Specifications: Dimensions: 65 mm × 32 mm × 4.2 mm (total height including text). Mounting interface: 5.5 mm diameter integrated hole, positioned for 4 mm of solid wall thickness to resist torsion. Lettering clearance: Text is extruded 1.2 mm above the base layer, providing enough depth for a mid-print filament swap if high-contrast text is desired. Material guidance: Prints cleanly in PETG or PLA. No brim required.
Wishbone Pendant with Windblown Ribbon
What it's for A classic organic wishbone pendant featuring an integrated chain loop and a dramatic, windblown ribbon tied at the neck. Designed with an entirely flat back so it drops straight onto the build plate, it captures a specific aesthetic silhouette in a ready-to-print form. Dimensions The pendant measures roughly 58 mm wide by 67 mm tall, giving it a bold presence that works well on a longer chain or cord. Print notes Since the back sits flush at Z=0, no supports are required. Print it flat. A smaller nozzle or lower layer height will help capture the dome of the bone and the taper of the ribbon tails perfectly.