Cucharilla de dos piezas con conector
Created today
Description
What it's for
Mango curvo tipo banana y conector independiente con dos pestañas flexibles. El conector encaja con un clic en el alojamiento del mango y se retira pellizcando las pestañas a través de las ventanas laterales, sin herramientas.
Dimensions
- Mango: 120 mm de largo, 25 mm de ancho en la base y 20 mm en la punta, 16 mm de grosor.
- Alojamiento: 16 × 6 mm, 23 mm de profundidad.
- Conector: núcleo de 22 mm, 5,6 mm de grosor, brazos de 1,6 mm con resalte de clic.
- Ventanas laterales de 4 mm donde se aloja el resalte.
Remix ideas
- Añadir una cabeza de cuchara en la pestaña tope del conector.
- Ajustar el grosor de los brazos (1,6 mm) para un clic más suave o más firme.
- Cambiar el radio de curvatura del mango.
Images
More like this
Explore more in Kitchen & Bathroom →
Galaxy Cap & Pets
A standalone pop-top can cover designed for easy swapping of customizable 3D-printable pets. Hooks for Remixing The Peg System: The mounting peg on the cap is a standard 3.8 mm cylinder, sitting slightly toward the back edge. Any custom object with a matching 4.2 mm socket will drop right on. Skull Profile: The flat skull on the cap is an exact scaled-down copy of the original 3D geometry. Expansion: Want to add more utility? You could stretch the cap base horizontally to house three or four pets simultaneously, or angle the peg so the figure faces upward when the can is open.
Obsidian — Ribbed Can Cooler with Handle
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports. Dimensions Inside diameter: 68 mm Inside height: 105 mm (above a 3 mm base) Wall: 2 mm, base: 3 mm Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel Features Diagonal ribs outside, perfectly smooth bore inside Rounded top rim Broad, rounded handle, 24 mm wide Flat front panel, 40 × 66 mm Print notes Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers No supports expected; fits a 180 mm build volume
Round Water Bottle With Cap
A round water bottle with a tapered shoulder, a 24 mm mouth and a separate slip-on cap. Printed as a hollow vessel with 3 mm walls. Remix hooks Body diameter and height: 70 mm wide, 170 mm straight section. Change these to resize capacity. Wall thickness: 3 mm. Raise it for watertight prints in PLA, or lower it with vase mode in mind. Neck: 24 mm bore, 30 mm outside. Swap the plain cap for a threaded one using a threaded rod and nut. Pairs with: a silicone gasket, a carry loop through the neck ring, or a sleeve that fits the 70 mm body. The cap is a friction fit and not a sealed closure. Test before filling.
Vented Snap-On Toothbrush Cover
A slide-on travel cover designed to enclose the head of a standard adult toothbrush. Protects bristles from crushing and external contact during transit, while the top-face perforations allow airflow so the brush can dry between uses. The base incorporates side-relief slits and internal retention bumps to snap securely over the neck of the brush, holding the cover in place in a travel bag. Interior cavity measures 26 mm wide, 16 mm deep, and 33 mm tall Vented top allows passive moisture escape Flex-slit base expands to accommodate varying handle tapers Snap-fit retention bumps grip the brush neck
Staggered 6-Mug Wall Rack
A heavy-duty wall rack designed to hold six mugs by their handles. The 280mm backplate staggers the layout into two distinct rows, ensuring wide ceramic rims have clearance and don't collide. Each peg tilts 12 degrees upward from the base to keep cups from sliding off under vibration. Remix Parameters Peg Dimensions: Built at 50mm long and 12mm thick for chunky handles. Shrink the diameter if you want to hang delicate teacups, or extend the length to stack espresso cups. Layout Grid: Peg centers are spaced roughly 90mm apart horizontally. The hull points can be compressed if you are short on wall space. Mounting Interface: Currently anchored by four 4.5mm countersunk screw holes. These can easily be swapped for slotted keyholes if the rack needs to be removable. Material & Strength: The pegs feature a 22mm flared base for leverage. If printing in a rigid, brittle filament like PLA, expanding that base diameter will add shear strength to the bottom row.
Sink Caddy With Drain Slots
Sponges and brushes left in a flat tray sit in a puddle and go sour. This sink caddy lifts them on ribs over a slotted floor so water runs out, and a separate tall holder takes a brush upright. Key numbers Tray: 200 x 110 x 45 mm, 2.4 mm walls Floor: 2.5 mm with 9 drain slots, plus 4 mm ribs to keep items off the surface Front notch: 60 mm wide, lets water pour off the front edge Brush socket: 48 mm square, inner opening 44 mm Removable holder: 40 x 40 x 100 mm with side slots for drainage; 2 mm clearance in the socket Printing Print the tray flat, no supports Print the holder upright 0.2 mm layers, PETG suggested for wet use