Dawn Bottle - 1.7in to 1in Adapter
Created 1 months ago
Description
Adapter designed to mate a 1.0-inch classic cap to the newer 1.7-inch Dawn dish soap bottle neck.
Fitment Notes:
- Base (Female): Fits over the 1.7" (43.18mm) male threads of the new bottle. Sized to 43.8mm inner diameter to provide clearance for FDM tolerances.
- Top (Male): Provides a 1.0" (25.4mm) male thread for the old cap. Sized to 25.2mm outer diameter so the factory plastic cap won't bind.
- Pitch: Modeled at roughly 6 TPI (4.23mm pitch), standard for most coarse bottle threads.
- Printing: The internal ceiling flat-bridges the gap from the wide base down to the 16mm bore. Prints as oriented without supports.
Images
More like this
Explore more in Kitchen & Bathroom →
CornerSlide — Shower Basket
This is a custom-fit modular shower basket meant for standard glass partitions. The L-shaped caddy hugs the corner, saving space while giving you plenty of room for soap and bottles. Features Heavy Drainage: 20x8 grid cut deep through the floor means zero water pooling. Adjustable Hangers: Print-in-place T-slot sliders let you click the hook to the exact width of your glass. Rugged Base: Printed flat to ensure the hangers won't snap under tension. Easy Print: Built in separate pieces to maximize bed adhesion and strength. Print Notes Lay the sliders flat. The rails have a slight overhang, so throwing some standard supports under the T-slot stem will help keep it crisp.
Toy Story Sky Cloud Cookie Cutter
A cookie cutter echoing the wallpaper clouds from Andy's room: a big bump on the upper left, smaller puffs along the top and a long flat base. The centre is open so dough passes straight through. 15 mm tall wall, about 1.2 mm thick, thin clean cutting edge on the flat bottom Widened rim at the top for pressing by hand About 100 mm wide, prints flat with no supports
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Obsidian — Ribbed Can Cooler with Handle
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports. Dimensions Inside diameter: 68 mm Inside height: 105 mm (above a 3 mm base) Wall: 2 mm, base: 3 mm Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel Features Diagonal ribs outside, perfectly smooth bore inside Rounded top rim Broad, rounded handle, 24 mm wide Flat front panel, 40 × 66 mm Print notes Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers No supports expected; fits a 180 mm build volume
Round Water Bottle With Cap
A round water bottle with a tapered shoulder, a 24 mm mouth and a separate slip-on cap. Printed as a hollow vessel with 3 mm walls. Remix hooks Body diameter and height: 70 mm wide, 170 mm straight section. Change these to resize capacity. Wall thickness: 3 mm. Raise it for watertight prints in PLA, or lower it with vase mode in mind. Neck: 24 mm bore, 30 mm outside. Swap the plain cap for a threaded one using a threaded rod and nut. Pairs with: a silicone gasket, a carry loop through the neck ring, or a sleeve that fits the 70 mm body. The cap is a friction fit and not a sealed closure. Test before filling.
GlideTrak — Under-Shelf Stemware Rack
GlideTrak is an under-shelf stemware storage block designed to securely hold up to four standard wine glasses upside down by their stems. The dual-channel architecture features a continuous track that flares wide at the opening, allowing smooth, one-handed retrieval and stowing of glasses without requiring precise visual alignment. Engineered as a robust mounting block, it secures flush against the underside of a cabinet while maintaining a clean profile. Features Flared Entry: The stem slot narrows from a 14 mm flared opening down to a 9 mm continuous track, guiding standard stems seamlessly into place. Concealed Mounting: Six countersunk holes with screwdriver access tunnels provide secure upward mounting, hiding the screw heads deep within the block. Support-Free Printing: Engineered to be printed standing vertically on its flat back wall, allowing the internal cavities to form cleanly without the need for support material. Dimensions Overall Footprint: 212 mm wide × 170 mm deep × 22 mm thick. Base Clearance: 82 mm wide internal cavity per channel to accommodate standard glass bases. Stem Track: 9 mm track width, expanding to a 14 mm flare at the front entry.