Made by orchidpanel
Created 2 days ago
Description
A flat diamond-shaped panel with diagonals of 7.5 in (190.5 mm) along X and 5.5 in (139.7 mm) along Y, 3 mm thick. A single orchid bloom with a short stem and two leaves is raised on the top face, with the top of the flower pointing toward the +X tip of the panel.
Images
Goldenrow is a plain, flat diamond panel: a clean blank with a 7.5 in diagonal along X and a 5.5 in diagonal along Y. With no raised artwork, it is a single flat slab that prints quickly with no supports. Dimensions Diagonals: 190.5 mm (7.5 in) along X, 139.7 mm (5.5 in) along Y Thickness: 3 mm Print notes Flat on the bed, no supports needed For speed: 0.6 mm nozzle, 0.3–0.4 mm layers, 2 walls, low infill (10–15%) and a fast top-surface setting Fits a bed of roughly 200 x 150 mm or larger
What it's for A flat diamond-shaped panel for signs, inserts, covers or decorative work. Four equal 6 in edges, flat faces. Dimensions Side length: 6 in (152.4 mm), all four sides Long diagonal: 8 in (203.2 mm) Short diagonal: about 8.94 in (227 mm), set by the side and long-diagonal lengths Thickness: 3 mm Remix ideas Add mounting holes at the corners. Round the points for a softer look. Emboss text or a logo on one face. Cut a window to make a frame.
A single flat picket fence panel, 100 mm long and 12 mm thick, with seven vertical pickets set 8 mm wide with 6 mm gaps between them. Two horizontal rails run the full length near the top and bottom, and the picket tips are rounded points that top out at about 27.2 mm. The pickets sit 4 mm in from each end, with the rails running through to the edges. The model is stored standing upright but is meant to print on its back face: laid flat, the 12 mm thickness becomes the print height and no supports are needed. Walls are 3 mm and the rails are 5 mm tall, so the part is sturdy at a small scale. Seven pickets, 8 mm wide with 6 mm gaps Two full-length rails, 5 mm tall Rounded pointed tips, roughly 27.2 mm overall height Print flat on the back face, no supports 3 mm walls, suited to PLA Use it as a miniature garden border, a diorama or model-railway accessory, or a small decorative edging piece.

A 120 mm tall decorative vase with a rounded, tapered body and vertical ribbing. A six-petal flower with stem and two leaves stands out from the front face. Height: about 120 mm; widest diameter about 60 mm Wall: 3 mm, 6 mm solid base Flower: raised relief on the -Y side Print upright; the flower relief may need supports or a brim Suited to dried flowers or as a shelf ornament; not watertight-rated
What it's for Zwei flache Buchstaben-L als Paar: ein normales L und eine spiegelverkehrte Version. Geeignet für Schablonen, Beschriftungen, Dekoration oder Modellbau. Dimensions Je Buchstabe: 40 mm breit, 102 mm hoch, 1,1 mm dick Strichbreite überall 9 mm Abstand zwischen beiden Buchstaben: 10 mm (gesamt 90 mm breit) Remix ideas Abgerundete Ecken oder Fasen an den Kanten Bohrungen zum Aufhängen oder Verschrauben Dickere Ausführung für mehr Steifigkeit
Toiture creuse de 192 × 103 mm pour une maison de 192 × 101,19 mm, hauteur 40 mm, avec pignons fermés percés chacun d'une fenêtre à 4 carreaux alignés. À vérifier avant impression Largeur de la maison : 101,19 mm (le toit déborde d'environ 0,9 mm de chaque côté). Longueur : 192 mm, pignons affleurant les murs. Caractéristiques Coque de 2,5 mm, dessous ouvert. Motif de briques sur les deux pentes. Demi-gouttières Ø3 mm ouvertes vers le haut. Fenêtres : 4 carreaux de 6 × 8 mm, montants de 2 mm. Incompatibilités Aucun ergot ni emboîtement : le toit se colle ou se maintient sur les murs.