Made by CarbonGimlet
Created 2 days ago
Description
A single flat picket fence panel, 100 mm long and 12 mm thick, with seven vertical pickets set 8 mm wide with 6 mm gaps between them. Two horizontal rails run the full length near the top and bottom, and the picket tips are rounded points that top out at about 27.2 mm. The pickets sit 4 mm in from each end, with the rails running through to the edges.
The model is stored standing upright but is meant to print on its back face: laid flat, the 12 mm thickness becomes the print height and no supports are needed. Walls are 3 mm and the rails are 5 mm tall, so the part is sturdy at a small scale.
Use it as a miniature garden border, a diorama or model-railway accessory, or a small decorative edging piece.
Images

Two mirrored flat picket fence panels for either side of a pedestrian crossing diorama. Each panel is 100 × 28 × 3 mm with seven rounded-point pickets joined by two horizontal rails. The pair spans 260 mm with a 60 mm gap for the crossing, fitting A4 landscape. Pickets: 8 mm wide, 6 mm gaps, rounded pointed tops Rails: 5 mm tall, near top and bottom, full 100 mm length Thickness: 3 mm throughout Print: flat on the bed, no supports, no holes, no text Material: PLA or PETG Footprint: 260 × 28 mm
What it's for A one-piece tabletop stand: a flat square foot with a single 14 mm square post rising from its centre. The broad 60 mm foot keeps the post stable on a desk or shelf, and the post gives you a square, straight upright to build onto, hang something from, or slot a part over. The underside carries a square sleeve socket with a wire hole through its floor, so a cable can be fed up through the post and out of the open top instead of running loose down the outside. It prints as one piece — nothing to glue or assemble. Dimensions Footprint: 60 × 60 mm, 8 mm thick, with a 1 mm chamfer around its edges. Post: 14 × 14 mm square, rising 90 mm from the centre of the foot. Overall height: 98 mm as it sits on the print plate. Underside socket: 14.5 × 14.5 mm square, 12 mm deep, centred in the foot and running 4 mm up into the post. Wire bore: 9 × 9 mm, running the full length of the post from the socket floor out through the open top, leaving about 2.5 mm of wall around it. Print notes Material: PLA on an FDM printer. Orientation: stands upright on its foot, so it prints with no supports. Walls: the post is bored out, so its walls are about 2.5 mm — a 3 mm perimeter setting will not fit them evenly; two or three perimeters gives a cleaner result. Slicing: set 20% infill in your slicer; the model itself does not carry an infill value. Remix ideas Change the post cross-section to match whatever has to slide over it, keeping roughly 0.5 mm clearance per side. Resize the socket to take a different sleeve, or cap the top of the bore to make a closed internal channel. Scale the foot wider or thinner for a heavier load or a tighter shelf space.
Goldenrow is a plain, flat diamond panel: a clean blank with a 7.5 in diagonal along X and a 5.5 in diagonal along Y. With no raised artwork, it is a single flat slab that prints quickly with no supports. Dimensions Diagonals: 190.5 mm (7.5 in) along X, 139.7 mm (5.5 in) along Y Thickness: 3 mm Print notes Flat on the bed, no supports needed For speed: 0.6 mm nozzle, 0.3–0.4 mm layers, 2 walls, low infill (10–15%) and a fast top-surface setting Fits a bed of roughly 200 x 150 mm or larger
A flat-pack kit for a three-storey, semi-detached Tudor-style house in OO scale, with the upper floors jettied out over the ground floor and a front gable on each house. The panels print flat with half-relief timber framing raised 0.6 mm. Windows and doors are separate pieces with small panes, joined by a thin web layer. Joined ground-floor and upper-floor front panels Front gables with small apex windows Outer side walls with horizontal and vertical timber beams Plain party wall, roof panels and a narrow base strip Separate windows and doors
A miniature grand piano that prints as one assembled piece: a curved case with a propped-open lid, four tapered legs, a music stand and a keyboard of 21 white keys running nearly the full width of the front. The body and black keys are PLA; the white keys are PETG, carried on a plate that drops into a recessed pocket in the case and is held in place by the key slip in front, so the two materials are retained mechanically rather than relying on PLA/PETG adhesion. Overall size: 100 × 75 × 61 mm. White key plate: 84 × 14 × 5.2 mm, 21 white keys with black keys in standard groups of two and three. PLA: case, lid, legs, music stand and black keys. PETG: white keys only. Print upright on its legs; the tilted lid overhangs and needs supports — keep them clear of the key pocket. Two separate colour regions: assign PLA and PETG to them in the slicer, use a purge tower and expect a fair amount of purge waste. The black keys are PLA, the same colour as the body, so they read as body colour unless the material is swapped. The model is a single watertight piece with no glue and no post-print fitting of keys or trim. Detail is sized for a 0.4 mm nozzle, and the widened keyboard leaves only a couple of millimetres of case wall at the front corners, so a well-tuned first layer helps there.
What it's for A flat diamond-shaped panel for signs, inserts, covers or decorative work. Four equal 6 in edges, flat faces. Dimensions Side length: 6 in (152.4 mm), all four sides Long diagonal: 8 in (203.2 mm) Short diagonal: about 8.94 in (227 mm), set by the side and long-diagonal lengths Thickness: 3 mm Remix ideas Add mounting holes at the corners. Round the points for a softer look. Emboss text or a logo on one face. Cut a window to make a frame.