Dwarven Rampart With Battle Scatter
Created 1 months ago
Remixed once
Description
A heavy tabletop defense rampart for 28mm-scale wargaming, featuring a wide walkway, solid rear stairs, and deep dwarven geometric cuts along the front.
Remix Hooks
- Scale: The wall sits at a 120mm width and 30mm height — scale the overall block if you're fielding larger forces.
- Scatter: The walkway holds a small 12x10mm dropped chest and a plunged sword. You can freely translate these across the
-YandXaxes, or replace them with your own fallen shields and banners. - Details: The geometric diamond cuts on the front face are modular — swap the depth or pattern to match your specific underground factions.
Images
More like this
Explore more in Automotive, RC & Hobby →
240mm Kidney Pool With Slide Receiver
A 1:6 scale kidney-shaped pool basin optimized for flat build plates, featuring an integrated U-channel slide receiver on the front edge. The structure prints as a single monolithic part with no overhangs requiring support material. The basin wall is swept to provide a soft 3mm top bevel, and the interior floor transitions via a 4mm chamfer to prevent sharp 90-degree corners that trap water or dirt. Dimensional Specs Max Footprint: 240 mm × 175 mm (fits standard 256 mm build volumes). Basin Height: 50 mm overall; 44 mm usable interior depth. Wall Thickness: 10 mm continuous structural wall. Slide Interface: 70 mm wide channel with 15 mm vertical retention walls and exactly 15 mm of socket depth to positive stop. Base Plate: Solid 6 mm thick floor, printing entirely flat to the bed.
OO Scale Low-Relief Georgian HouseKit
A low-relief flat-pack Georgian building scaled for OO gauge (4mm to the foot). The kit prints flat and features inner 45-degree miters on the walls for clean 90-degree outer corners. Remix Hooks Scale: Set up for OO (1:76), but scales down to N or up to O nicely if you check your tolerances on the drop-in parts. Clearances: The windows and doors are designed with a slight undersize to allow for a coat of paint before dropping them in. Roofs: Sized at 35mm deep to give a 5mm overhang past the 30mm side walls, and long enough to meet at the ridge and clear the eaves. They feature a stepped slate/tile texture.
Lego piece for wagon door runner with thinner teeth bit slightly smaller
Wagon door runner to replace 3 off 15208 bricks Version with slightly too large slope
Sistema de Dirección Ackermann2
Sistema de dirección frontal mecánico tipo Ackermann, diseñado para vehículos a radiocontrol o maquetas. Las manguetas descansan sobre el eje rígido principal y se conectan mediante una barra de acoplamiento, asegurando que la rueda interior trace un radio de giro más cerrado que la exterior durante las curvas. Puntos de Modificación Este diseño está pensado como una plataforma base para integrarse en chasis personalizados. Las cotas actuales sirven como punto de partida: Ancho del eje: 100 mm totales, con 90 mm entre los centros de pivote. Geometría Ackermann: Los brazos de dirección tienen una longitud de 20 mm y un ángulo de inclinación interna de 15 grados. Tornillería: Los orificios en el eje y la barra son pasantes de 3.2 mm, mientras que las manguetas cuentan con orificios de 2.8 mm diseñados para que tornillos M3 muerdan directamente en el plástico. Ejes de rueda: Los vástagos laterales miden 5 mm de diámetro por 18 mm de largo, compatibles con rodamientos estándar de RC 5x10 o hexágonos adaptadores.
Sweeping Dollhouse Window Slide
A large 3D-printable playground slide designed to mount securely into a 90 mm window frame, sized for 1:6 scale dolls. The track follows a single smooth clockwise sweep out and away from the dollhouse, transitioning cleanly to the floor. Broad Descent: Uses a smooth Bezier sweep to drop 460 mm without looping or reversing direction. Upright Geometry: The track remains perfectly level across its width from top to bottom. Window Mount: Features a squared notch that drops cleanly over a standard lower window edge.
60mm Arc Reactor LED Ring
Circular mounting ring for standard 5mm LEDs. Sized with a 60mm outer diameter and a 48mm pitch circle. Features a continuous recessed channel on the rear face to simplify wire routing and soldering, plus a stepped front lip to seat a custom diffuser plate. Outer Diameter: 60.0 mm Inner Diameter: 36.0 mm Thickness: 5.0 mm LED Fitment: 5x 5.2mm bores (72° spacing) Rear Recesses: 6.2mm flange countersinks with an 8mm wide wire track Front Groove: 1.0 mm deep, accommodates a 56mm OD diffuser