Yuletide Vault — 24-Drawer Advent Calendar
Created today
Description
A print-in-place advent calendar with 24 identical sliding drawers in a 4 × 6 grid. Every drawer front carries an engraved number from 1 to 24 and a soft-edged finger handle, so the countdown opens one small compartment at a time. The drawer bodies, fronts and matching frame openings keep clean square corners; only the handles are rounded, giving a comfortable grip without softening the rest of the geometry. Each cavity is sized around a 35 mm × 20 mm candle, making the drawers practical for a daily treat or a small gift. The whole assembly fits the Bambu Lab A1 Mini build plate and prints without supports in the sliding channels.
Features
- 24 identical drawers arranged in 4 columns and 6 rows, numbered 1–24.
- Square drawer bodies, fronts and frame openings; only the handles are softened, with an edge radius of about 1.5–2 mm.
- Each drawer has an 11 × 7 mm handle that protrudes 3 mm, centred on the front.
- Engraved numbers sit 0.6 mm deep in the strip above each handle, clear of the grip area.
- 0.4 mm clearance on every side and at the back keeps the drawers sliding freely.
- A stop ridge inside each pocket catches the drawer's back wall after about 40 mm of travel, so drawers cannot fall out accidentally.
- Drawer cavity: 38.5 × 42 × 22 mm, sized to hold a 35 × 20 mm candle.
Dimensions
- Overall footprint: 175.2 × 154.2 × 49.6 mm including handles — fits the A1 Mini's 180 mm plate.
- Drawer outside: 41.5 × 45 × 23.5 mm; wall and floor thickness: 1.5 mm.
- Frame divider walls: 1.2 mm.
Print notes
The calendar prints as one piece with the drawers already seated in the frame. The back face lies flat on the plate and the fronts and handles face up, which avoids supports in the channels. Print in white PLA for the intended look.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Print-in-Place Articulated Dragon Fidget Toy
Articulated dragon with a horned head, ten hinged body segments and back spikes. It prints as one piece with no assembly, and the body flexes in a wave when held. Joints: pin hinges with 0.4 mm clearance per side, alternating between side-to-side and up-down bending Segments: 10, tapering from an 18 mm wide head to a narrow tail Size: about 155 mm long, 12 mm tall without spikes Print: lay flat, no supports intended for the body; 0.2 mm layers, PLA or PETG After printing: bend each joint back and forth to break the hinges free Use: desk fidget, sensory toy
Women's Sunglasses Frame with Folding Arms
Printed sunglasses where the parts crowd each other on the plate and fuse: this set lays the frame, two folding arms, ribbon inserts and hinge pins out with clear space between them. Frame width: 145 mm, 50 mm tall, 5 mm plate, hinge ears 18.5 mm high Lens openings: 50 × 36 mm each, 16 mm bridge gap Arms: about 139 mm long, 8 mm wide, 6 mm thick, with at least 4.8 mm between each part on the plate Hinge pins: four, 2 mm across, in 2.4 mm holes Hearts and breast cancer awareness ribbons recessed 1 mm on the frame and arms Print flat, no supports needed for the arms
Round Button With Raised Rim
A flat round button with a raised, rounded outer rim and four holes at the centre, so thread or a finger doesn't slide off the edge. Key numbers Diameter: 50 mm Face thickness: 3 mm, rim peaks at 5 mm Rim: 5 mm round bead around the edge Holes: four 4 mm holes in a 12 mm square pattern Print: flat side down, no supports, 0.2 mm layers
Pickleball Paddle Name Stamp with Handle
Custom ink stamp showing a tilted pickleball paddle with a perforated pickleball in the head and the name "Pat" centered below. The design is mirrored so it prints correctly when stamped, and a flared grip handle sits on the back of the plate. Plate: 62 × 86 mm base, 4 mm thick, rounded corners Relief: 2 mm raised design, paddle tilted 35° Ball: 17 mm diameter with 19 holes (1 center, 6 inner ring, 12 outer ring) Handle: 22 × 38 mm stem with 34 × 44 mm cap, about 36 mm overall height Print orientation: design face down on the bed, no supports needed
Schild 200 x 100 x 8 mm Sauerteig
Schild mit zweizeiliger Beschriftung "Natur" und "Sauerteig" und einer Aufhängeöse oben mittig. Platte schwarz, Schrift weiß und erhaben, als ein zusammenhängendes Teil für Mehrfarbdruck. Platte: 200 × 100 × 8 mm, Ecken gerundet Öse: 30 mm Außendurchmesser, 14 mm Loch, Gesamthöhe 120 mm Schrift: 32 mm hoch, 0,6 mm erhaben, 0,2 mm eingelassen Druck: Drucker mit automatischem Filamentwechsel (z. B. AMS), 3MF empfohlen
Magic octagon coin.
An octagon coin whose raised arrow disappears into the bed side: the underside is now flat with the arrow cut in as a shallow dent, so no layer prints over empty air. Size: 50 mm across corners, 3 mm body, 4.2 mm total height. Top: 0.6 mm raised rim, with the arrow rising 1.2 mm so it stands 0.6 mm above the rim. Change filament at that layer to colour only the arrow. Underside: flat, with a 0.6 mm deep arrow indentation turned 90° from the top arrow, plus a 1.4 mm wide, 0.6 mm deep groove about 2 mm in from the edge. Print: lie it flat, underside on the bed, no supports.