Made by BobertPrints
Created yesterday
Description
A miniature grand piano that prints as one assembled piece: a curved case with a propped-open lid, four tapered legs, a music stand and a keyboard of 21 white keys running nearly the full width of the front. The body and black keys are PLA; the white keys are PETG, carried on a plate that drops into a recessed pocket in the case and is held in place by the key slip in front, so the two materials are retained mechanically rather than relying on PLA/PETG adhesion.
The model is a single watertight piece with no glue and no post-print fitting of keys or trim. Detail is sized for a 0.4 mm nozzle, and the widened keyboard leaves only a couple of millimetres of case wall at the front corners, so a well-tuned first layer helps there.
Images
A single flat picket fence panel, 100 mm long and 12 mm thick, with seven vertical pickets set 8 mm wide with 6 mm gaps between them. Two horizontal rails run the full length near the top and bottom, and the picket tips are rounded points that top out at about 27.2 mm. The pickets sit 4 mm in from each end, with the rails running through to the edges. The model is stored standing upright but is meant to print on its back face: laid flat, the 12 mm thickness becomes the print height and no supports are needed. Walls are 3 mm and the rails are 5 mm tall, so the part is sturdy at a small scale. Seven pickets, 8 mm wide with 6 mm gaps Two full-length rails, 5 mm tall Rounded pointed tips, roughly 27.2 mm overall height Print flat on the back face, no supports 3 mm walls, suited to PLA Use it as a miniature garden border, a diorama or model-railway accessory, or a small decorative edging piece.

Two mirrored flat picket fence panels for either side of a pedestrian crossing diorama. Each panel is 100 × 28 × 3 mm with seven rounded-point pickets joined by two horizontal rails. The pair spans 260 mm with a 60 mm gap for the crossing, fitting A4 landscape. Pickets: 8 mm wide, 6 mm gaps, rounded pointed tops Rails: 5 mm tall, near top and bottom, full 100 mm length Thickness: 3 mm throughout Print: flat on the bed, no supports, no holes, no text Material: PLA or PETG Footprint: 260 × 28 mm
A flat-pack kit for a three-storey, semi-detached Tudor-style house in OO scale, with the upper floors jettied out over the ground floor and a front gable on each house. The panels print flat with half-relief timber framing raised 0.6 mm. Windows and doors are separate pieces with small panes, joined by a thin web layer. Joined ground-floor and upper-floor front panels Front gables with small apex windows Outer side walls with horizontal and vertical timber beams Plain party wall, roof panels and a narrow base strip Separate windows and doors
A chunky, build-it-yourself two-speed constant-mesh transmission that turns mechanical principles into a tangible display piece. Gears and shafts lie flat on the plate for straightforward printing, and the base plate carries a bold BENZE nameplate where the original labels once sat. The open frame shows the internals clearly, making it a handy desk-side demo of how a constant-mesh gearbox shifts ratio. Design Features Two-Speed Setup: Includes a 15-tooth and 25-tooth spur gear arrangement. Constant Mesh: The gears are always engaged. A sliding dog clutch (the dog slider) locks the freely spinning gears to the output shaft to change the ratio. Assembly: Parts drop onto the base frame's posts. The high gear goes on the top of the output shaft (pocket facing down), the low gear goes on the bottom (pocket facing up), and the slider sits in between them on the hex shaft. Nameplate: The base plate is personalized with the name BENZE, replacing the former ENGINE, WHEELS, and SHIFT labels.
What it's for Ten OO scale (4 mm to the foot) window frames and four panelled doors, held on thin web sheets for printing and painting as a batch. Each door carries a raised handle and a letter box recess. Dimensions Windows: 20×17, 16×17, 12×16.5, 16×16.5, 12×16.5 mm (two rows of five), each with one transom and one mullion Doors: 12×24.5 mm, four in a row, 1.5 mm thick Door handle: raised 0.6 mm on the centre rail, right-hand side Letter box: 5×1.2 mm dip, 0.6 mm deep, left of the rail Web layers: 0.6 mm thick, open through the window panes Remix ideas Cut the webs away after printing, or trim them to the frames Move the letter box to the upper panel Swap the lever for a round knob
What it's for Zwei flache Buchstaben-L als Paar: ein normales L und eine spiegelverkehrte Version. Geeignet für Schablonen, Beschriftungen, Dekoration oder Modellbau. Dimensions Je Buchstabe: 40 mm breit, 102 mm hoch, 1,1 mm dick Strichbreite überall 9 mm Abstand zwischen beiden Buchstaben: 10 mm (gesamt 90 mm breit) Remix ideas Abgerundete Ecken oder Fasen an den Kanten Bohrungen zum Aufhängen oder Verschrauben Dickere Ausführung für mehr Steifigkeit