Gazebo Silhouette Hexagonal Bird Feeder
Created today
Description
Bring a touch of classic park architecture to the garden with this gazebo-inspired hexagonal bird feeder. The design pairs a rigid geometric central column with a sweeping, wrap-around tray that allows visitors to land from any approach angle. A slip-fit peaked roof completes the silhouette while keeping the seed reservoir dry and accessible for top-down refills.
Structural Features
- Hexagonal Reservoir: A 100mm-wide central tube holds seed while maintaining a clean, structured profile.
- Omnidirectional Perch: The extended base functions as both a 360-degree landing ledge and a feeding trough.
- Regulated Flow: Six 8mm by 25mm dispensing slots are positioned precisely at the base of the column to provide an even distribution of seeds.
- Hanging Apex: A sturdy loop is integrated directly into the roof peak for straightforward suspension from a branch or bracket.
Images
More like this
Explore more in Home & Fixtures →
bird bath shower head 5/16" 2
A friction-fit spray nozzle designed to convert a standard 5/16" ID water line into a wide, gentle shower for a bird bath or fountain. The part is modelled upside down (spray face flat on the Z-plane) so it prints cleanly as a single hollow body without any internal or external supports. Parameters to Play With If you take this into your own setup, here are the numbers driving the shape: The Stem Fit: Tapers from 8.5mm down to 7.2mm over a 20mm length. This is the sweet spot to wedge tightly into soft 5/16" (7.94mm) tubing without blowing out under mild pump pressure. The Spray Face: A 45mm outer diameter with a flat 2mm-thick face plate. The Holes: Uses a grid of 1.5mm holes spaced 3.5mm apart. Remix Hooks Flow Rate: If your pump is struggling to push water through, widen the internal 4.5mm bore or bump the face holes from 1.5mm up to 2.5mm. Directional Spray: Instead of a full grid of holes, mask off half the face to create a directional fan spray. Barbs: The smooth taper seals well for low pressure, but if you're running higher pressure, swapping the smooth cone for a stepped barbed profile will lock the tubing down harder.
Garage Vent to 6-Inch Adapter
A custom 2-part venting adapter designed to connect a 360x210mm drywall vent gap to a standard 6-inch exhaust duct. Two-Part Assembly: Splits perfectly down the middle with a 10mm external flat flange for easy gluing. Tapered Male Fitting: Connects securely inside standard 6-inch ducting. Support-Free Print: Internal lofts are designed to print cleanly with no supports while encouraging laminar exhaust flow. Mounting Integration: Six #6 screw holes for securing to drywall, with an extended bottom footing to rest cleanly on a garage concrete foundation.
Modular PEX Hub with Stake
An inline four-way tee fitting for standard 1/2" PEX, featuring an integrated top-mounted adjustable water dripper. Built to string together in series for garden irrigation loops. This version features a modular two-piece base, splitting the long ground stake away from the main distribution body. Connections: Four 1/2" PEX barbs form a versatile hub. Unused branches can be sealed with the included block-off cap. Metering: A threaded upper cap with an internal conical needle regulates flow rate out of a 2mm orifice. Removable Stake: A heavy-duty 6-inch threaded stake screws firmly into the bottom of the hub, printing flat for strength. Printing Note: The separated stake prints easily lying down, while the base requires supports beneath the horizontal barbs to print correctly on the bed.
Angled-Entry Tomato Vine Clips
A set of dual-loop clips designed to secure growing tomato vines to standard 1cm bamboo stakes. The vine loop features a 45-degree angled entry slot, allowing stems to be guided in without threading or bending delicate tips, while the generous internal diameter leaves room for the stem to thicken over the season. Remix Hooks Stake Bore: Currently set to a 10mm inner diameter with a 6.5mm snap gap. Adjust this to match 8mm or 12mm garden stakes. Vine Capacity: The vine loop sits at 15mm ID to accommodate mature tomato stems. Scale this up for heavy-set cultivars or down for peppers and beans. Entry Angle: The 6mm vine slot is positioned at 45 degrees to prevent accidental slip-outs. Adjust the angle or narrow the gap for vines that need a tighter capture. Thickness: Extruded to 8mm, giving the stake loop enough surface area to grip securely when printed in PETG or PLA.
AeroSpan — Sliding Window AC Seal
Built for horizontal sliding windows, this adjustable dual-plate system fills the open sash gap without permanent modifications, making it ideal for rentals. It features a precise 130mm port for portable air conditioner hoses and includes a twist-lock bayonet cap to completely seal off drafts when the cooling unit is disconnected. Features Adjustable Span: The sliding track design expands the working width from 340mm up to 500mm to accommodate varying window openings. Rental Friendly: Clamps securely using standard hardware rather than relying on window pressure or requiring drilled fixtures. Twist-Lock Cap: A secure three-lug bayonet mechanism blanks off the 130mm port for times when the hose is removed. Assembly Notes The sliding extension requires four standard M6 bolts and nuts (not included in the printed file) to clamp the overlapping plates once the desired width is set.
Olympus — Modular Tall Planter
Olympus is a three-piece modular planter designed specifically for succulents, bonsai, and trailing vines that benefit from elevation without requiring a massive volume of soil. The fluted Greek column design prints cleanly in three support-free segments. The lower pedestal features a hollow core designed to be filled with sand or gravel for substantial bottom-weight, preventing the tall assembly from tipping. The upper capital locks onto the base and contains an internal water catch basin, while the dedicated nursery insert drops cleanly into the top with a full grid of drainage holes. Dimensions Total Assembled Height: 350 mm Maximum Diameter (Capital): 175 mm Nursery Insert Cavity: 149 mm diameter x 82 mm depth (approx. 1.4 liters) Print Notes Supports: None required. All overhangs and internal cavities are drafted for support-free bridging. Clearances: The slip joint and nursery drop-in feature 0.3mm and 1.0mm radial clearances respectively. Assembly: Print the three pieces separately. Fill the Base Pedestal with dry sand, then seat the Capital Planter on top (use CA glue on the slip joint for a permanent bond). Drop the populated Nursery Insert into the top.