Made by a Guest
Created today
Description
A 25 mm square corner block, 8 mm tall, with a quarter-circle channel on top that seats a 10 mm LED strip and turns it 90 degrees. Made for under-shelf lighting where the strip needs to follow an inside corner without kinking. The underside is flat, so it takes adhesive tape or double-sided foam.
The channel is 10 mm wide and 4 mm deep, with a 12.5 mm centerline radius. It enters and exits through the two sides that meet at the far corner. Vertical corners carry a 1 mm chamfer.
Images
Replacement two-way joiner for the top-front-center of a fiberglass-rod printer enclosure. It splices two nominal 8.2 mm rods end-to-end and carries a flat-lying arm with a screw boss for a Sercomm RC8110 camera. Print it as one piece with the arm flat on the bed, then rotate the part about the rod axis during installation to aim the camera downward and toward the bed center. Specifications Rod sockets: 8.35 mm ID, 30 mm deep per side, 0.5 mm entry chamfers, separated by a 3 mm solid center stop; 63 mm overall sleeve length. Sleeve: approximately 14.35 mm OD with 3.0 mm wall thickness. Arm: 20 mm wide and 6 mm thick, extending 50 mm from the sleeve, with a root block and gusset blending it into the sleeve. Camera boss: 28 mm diameter and 6 mm thick, with a 6.6 mm through-hole and a 12 mm × 2 mm counterbore for a 1/4"-20 camera screw. Print footprint: 63 × 71.2 × 14.4 mm as oriented on the plate; the teardrop socket bores and flat arm are intended to print without support. Fit: press-fit for measured 8.19–8.20 mm rods; PETG wall thickness is sized to resist splitting and bending from the tensioned enclosure fabric.

A table lamp stand with a twisted six-lobe column rising from a round base to a cup that holds a standard E27 lamp socket. A 12 mm bore runs down the centre and a 7 mm channel carries the cable out the back of the base, so the wiring stays hidden. Remix hooks Socket pocket: 40.6 mm diameter, 26 mm deep. Measure your socket body and adjust socket_d before printing; many holders vary by a millimetre or two. Twist and lobes: 120° twist, 6 lobes. Change the twist angle for a gentler or more dramatic spiral, or the lobe count for a different silhouette. Height: the column is 140 mm; total height is about 182 mm. Taller columns suit larger shades. Base: 120 mm diameter, 8 mm thick. Widen it or add weight (coins, steel washers) for large shades. Set-screw hole: a 3.2 mm cross hole near the cup top is there for an M3 grub screw to lock the socket. Pairs with: an E27 socket with threaded nipple or clip-in body, a fabric cord with inline switch, and any E27 drum or cone shade. Print upright without supports. Use mains-rated, certified electrical parts, and a low-heat LED bulb rather than incandescent.
This T pipe inlet joins a 31 mm line to a 41 mm line instead of stacking adapters that leak at every joint. The main run holds its 41 mm outside diameter all the way past the side branch, then necks down through a short taper to a 31 mm spigot long enough to grip a hose or slide into a coupling. The plate carries two identical copies side by side, 70 mm apart along Y, so one print gives you a pair; each copy is a separate hollow part with nothing to assemble. Fit and print notes Two identical pipes laid out side by side, 70 mm apart across Y Main run: 84 mm long overall per pipe — the 41 mm OD section carries on past the branch to within a few millimetres of its edge before reducing 41 mm centre section: 48 mm long Taper: 6 mm, from 41 mm OD down to 31 mm OD Reduced end: 30 mm of straight 31 mm OD spigot Other end: stays at the full 41 mm OD, no reduction Side branch: 31 mm OD, 45 mm out from the centreline Bores: 26 mm through the 31 mm spigot and the branch, 36 mm through the 41 mm section Wall thickness: 2.5 mm throughout Sits flat on the plate, no supports needed Only one end reduces, so orientation matters when you install it. The 84 mm length is what keeps the branch on the full-size section — check the gap before you commit, and dry-fit the 41 mm end first if it has to butt against something.

A 250 × 30 mm incense holder with a shallow trough running its full length, so ash from a burning stick lands in the channel and stays off the shelf. A raised block at one end carries a 3 mm stick hole angled 35° out over the trough. The channel continues underneath the block, so ash drops straight into it. Remix hooks Stick hole diameter (3 mm): The default is snug for thin sticks. Open it to 3.3–3.6 mm for thicker ones, or to about 2.5 mm for fine sticks. Hole angle (35°): A steeper angle makes the stick stand more upright and shortens the ash path. A shallower one lengthens the burn path and needs a longer tray. Trough depth (5 mm) and floor (2 mm): Deepen the trough for loose ash or to hold a layer of sand. The side walls are 2 mm, so widening the trough thins them. Overall length (250 mm): This is a free choice. Shorten it for shorter sticks. The block is 30 mm long and 22 mm tall. Block height (22 mm): Raise it to let longer sticks clear the tray end. Pairs with A thin layer of sand or ash in the trough to catch embers. Multiple holes along the block for several sticks. A lid or cover cut from a flat strip for storage. Print flat with the base down. The angled hole is drilled through the block, so check how your slicer handles the overhang at the angle and consider supports if it sags.

GripRoot is a replacement cane tip for a 19 mm tube, built for the case where an old tip has worn through and started to clack. A wide 40 mm base spreads the load, a tapered body leads up to a deep socket, and a cross-hatch tread on the underside gives grip on wet floors. The grooves run straight out through the edge of the base, so water has a path to escape instead of pooling under the tip. Dimensions Base diameter: 40 mm, with a chamfered lower edge Overall height: 31 mm Neck diameter at the top: 29 mm Socket: 19.5 mm inner diameter, 25 mm deep Socket mouth: small flared lead-in to help the tube seat Tread Cross-hatch grid of grooves, 3 mm wide and 2.5 mm deep 6 mm pitch in both directions Grooves open at the base edge for drainage Print notes Designed for stiff TPU, printed base-down with no supports needed The 19.5 mm socket against a 19 mm tube gives roughly 0.5 mm of interference, which suits a flexible material Measure the actual tube before printing, since nominal 19 mm tubing often varies slightly Adjust socket diameter or groove depth if a tighter grip or a more aggressive tread is wanted
The wood at the bottom of a hamper leg is the first thing to go: it stands in whatever puddle the bathroom floor collects, drinks it up, and goes soft until the basket slumps and rocks. This sleeve slides onto the end of one rectangular wooden leg, holds the wood about 9 mm clear of the floor, and slopes its pocket floor so splash water runs out the sides instead of sitting in there against the wood. What it does Pocket: 31 × 15 mm inside, sized exactly to the leg with no added play — that measurement already accounts for clearance. 15 mm deep at its shallowest point, the centre ridge, and deeper toward the sides where the floor falls away. Stand-off: a single arched cut runs the full depth of the underside, leaving two flat feet that hold the leg about 9 mm off the floor. Overall height is about 27 mm. Drainage: the pocket floor is a shallow ridge sloping down to both long sides, with one 16 mm slot through each long wall at the low edge. Water leaves sideways, and the slot bottoms sit 10.5 mm above the floor, so no opening rests in the wet. Each slot is pointed at the top rather than flat-roofed, which is what lets it print clean. Shape: 1.2 mm chamfer at the opening to get it started over the wood, 3 mm rounding on the vertical and top edges so it doesn't snag a mop or a bare toe. The bottom edges are left sharp so they sit flat on the bed. Printing it Print in PETG with the sleeve opening facing up and the two feet on the bed — no supports anywhere. The arch sides are 45°, so the only bridge is the flat strip about 6 mm across the roof of the arch. The finished part measures roughly 36 × 20 × 27.2 mm, walls 2.5 mm thick. A plain matte finish in white, grey or black sits well in a bathroom. A zero-clearance pocket is tight in PETG. Check the leg with calipers before printing if the wood looks swollen or tapered — if it won't slide on, the pocket wants a few tenths opening up.