Made by ChromeSturgeon
Created 1 months ago
Description
A single-piece desktop stand designed to hold and display a standard trading card in a rigid plastic top loader (approx. 76 × 102 mm). It captures the bottom edge of the sleeve while keeping the artwork fully unobstructed behind a deep U-shaped front cradle, pitched back at a 12-degree viewing angle.
Designed to print entirely without supports in a flat, natural orientation. The geometry has been tuned to ensure clean external overhangs and uses generous radiuses everywhere to maintain strength around the captured slot. Recommended for standard FDM printing.
Images
A miniature grand piano that prints as one assembled piece: a curved case with a propped-open lid, four tapered legs, a music stand and a keyboard of 21 white keys running nearly the full width of the front. The body and black keys are PLA; the white keys are PETG, carried on a plate that drops into a recessed pocket in the case and is held in place by the key slip in front, so the two materials are retained mechanically rather than relying on PLA/PETG adhesion. Overall size: 100 × 75 × 61 mm. White key plate: 84 × 14 × 5.2 mm, 21 white keys with black keys in standard groups of two and three. PLA: case, lid, legs, music stand and black keys. PETG: white keys only. Print upright on its legs; the tilted lid overhangs and needs supports — keep them clear of the key pocket. Two separate colour regions: assign PLA and PETG to them in the slicer, use a purge tower and expect a fair amount of purge waste. The black keys are PLA, the same colour as the body, so they read as body colour unless the material is swapped. The model is a single watertight piece with no glue and no post-print fitting of keys or trim. Detail is sized for a 0.4 mm nozzle, and the widened keyboard leaves only a couple of millimetres of case wall at the front corners, so a well-tuned first layer helps there.
What it's for A one-piece tabletop stand: a flat square foot with a single 14 mm square post rising from its centre. The broad 60 mm foot keeps the post stable on a desk or shelf, and the post gives you a square, straight upright to build onto, hang something from, or slot a part over. The underside carries a square sleeve socket with a wire hole through its floor, so a cable can be fed up through the post and out of the open top instead of running loose down the outside. It prints as one piece — nothing to glue or assemble. Dimensions Footprint: 60 × 60 mm, 8 mm thick, with a 1 mm chamfer around its edges. Post: 14 × 14 mm square, rising 90 mm from the centre of the foot. Overall height: 98 mm as it sits on the print plate. Underside socket: 14.5 × 14.5 mm square, 12 mm deep, centred in the foot and running 4 mm up into the post. Wire bore: 9 × 9 mm, running the full length of the post from the socket floor out through the open top, leaving about 2.5 mm of wall around it. Print notes Material: PLA on an FDM printer. Orientation: stands upright on its foot, so it prints with no supports. Walls: the post is bored out, so its walls are about 2.5 mm — a 3 mm perimeter setting will not fit them evenly; two or three perimeters gives a cleaner result. Slicing: set 20% infill in your slicer; the model itself does not carry an infill value. Remix ideas Change the post cross-section to match whatever has to slide over it, keeping roughly 0.5 mm clearance per side. Resize the socket to take a different sleeve, or cap the top of the bore to make a closed internal channel. Scale the foot wider or thinner for a heavier load or a tighter shelf space.
What it's for Zwei flache Buchstaben-L als Paar: ein normales L und eine spiegelverkehrte Version. Geeignet für Schablonen, Beschriftungen, Dekoration oder Modellbau. Dimensions Je Buchstabe: 40 mm breit, 102 mm hoch, 1,1 mm dick Strichbreite überall 9 mm Abstand zwischen beiden Buchstaben: 10 mm (gesamt 90 mm breit) Remix ideas Abgerundete Ecken oder Fasen an den Kanten Bohrungen zum Aufhängen oder Verschrauben Dickere Ausführung für mehr Steifigkeit
Toiture creuse de 192 × 103 mm pour une maison de 192 × 101,19 mm, hauteur 40 mm, avec pignons fermés percés chacun d'une fenêtre à 4 carreaux alignés. À vérifier avant impression Largeur de la maison : 101,19 mm (le toit déborde d'environ 0,9 mm de chaque côté). Longueur : 192 mm, pignons affleurant les murs. Caractéristiques Coque de 2,5 mm, dessous ouvert. Motif de briques sur les deux pentes. Demi-gouttières Ø3 mm ouvertes vers le haut. Fenêtres : 4 carreaux de 6 × 8 mm, montants de 2 mm. Incompatibilités Aucun ergot ni emboîtement : le toit se colle ou se maintient sur les murs.
Toit à deux pentes creux, ouvert en dessous, dont le bas des pentes se termine au milieu de gouttières arrondies en U, de sorte que seule la moitié extérieure du canal reste visible. Joints d'ardoise gravés sur les deux pentes. Pistes de remix Hauteur du toit : 40 mm au faîtage, donc des pentes d'environ 36°. Réduire cette valeur donne un toit plus plat. Gouttière : profil de 5 × 4 mm, canal rond de 3,4 mm. Élargir le canal pour un meilleur écoulement. Position de fin de pente : le bas des pentes s'arrête à 54,5 mm de l'axe, au centre du canal. Décaler cette valeur change la part de gouttière visible. Compatible avec un garage de 192 mm de large à quatre portes de 40 mm.

A wall sign that reads Creative in a brushed script — the fix for a sign that ends up a plain rectangle of plastic with the lettering lost inside it. The backing follows the outline of the letters instead of being a plate, and a raised border traces that same shape, so the sign keeps the word's silhouette on the wall rather than a slab around it. Because the border, backing and lettering are separate colour areas, you can swap filament at the layer changes and get a two- or three-tone sign off a single-colour printer. Sizes Overall footprint: 126 × 49 mm Lettering: 116 × 29.5 mm, 3 mm proud of the backing Backing: 2 mm thick, cut to the lettering outline Border: 5 mm tall, rounded, tracing the same outline Hanging: one round tab above the lettering with a 4 mm hole Hang it from the single tab — check the tab clears your hook or screw head before you commit to a wall position. Print flat on the backing, no supports needed.