MoogMatch — Vertical 6HP Pod

Motorcycle Numberplate Spray Deflector/Mud Guard

That perfectly aligned stripe of wet road grime the rear tire slings exactly past the bottom edge of the plate and up the center of your jacket is miserable. Tail tidies look good, but they leave the dead center of the wheel completely unshielded. This is a wedge deflector that clips directly onto the bottom edge of the numberplate. It projects a downward-angled, 18mm shelf backwards toward the wheel, catching that specific arc of water and directing it back at the road. The ends are heavily swept to match the sharp lines of modern sport bikes like the Z-series. Fitment & Printing Slot Width: 3.0mm, deep enough (15mm) to swallow standard plates. Features an internal 0.4mm friction ridge to bite onto the plate. (If your plate is very thin stamped metal, add a strip of double-sided tape inside the channel). Deflection Range: 90mm wide to cover the tire's central spray path, with an 18mm rearward overhang. Print Orientation: Drop it flat on its front face in your slicer. The awning prints upwards at an angle, meaning the whole piece prints cleanly with zero supports. Material: PETG or ABS/ASA strongly recommended. PLA will warp from exhaust heat or summer sun.

11 days agoRemix →

Print-in-Place Flexible Crocodile

Toy reptiles are fine until you try to pose them and realise they're cast into a single, rigid block that snaps if you push it. This fixes that. It’s an eight-segment articulated crocodile that prints entirely assembled, right on the bed. The joints are enclosed captive hinges with a 0.45mm clearance, meaning they fuse just enough structure to print safely before breaking free instantly for a massive range of motion. The body tapers from a stylized head down to a narrowed tail, with distinct rib extensions and legs built into the mid-sections. Print Instructions Clearance: 0.45mm gaps in the hinges — make sure your flow rate is dialed in to avoid the joints fusing. Layer Height: 0.2mm recommended. The internal pin tapers rely on standard layer heights to bridge successfully. Adhesion: It prints flat. No brim is required unless you have severe warping issues on small footprints (like the tail tip). Supports: None. The hinge pins use 45-degree chamfers so they print perfectly in mid-air inside their sockets.

15 days agoRemix →

nested tictacto

2 days agoRemix →

V-Drums Tripod-mount Rack Clamp

A custom-fit clamp for 1.5" Roland V-Drums rack tubes that provides a standard 1/4"-20 tripod mounting point. Designed to hold cameras, field recorders, or metronomes directly on your drum hardware. Features: Specifically sized for 38.5mm electronic drum rack tubes Captive hex pocket for a 1/4"-20 tripod bolt on the inside curve (bolt won't spin once clamped) Uses two M6x35mm bolts and nuts for the main clamp tension Prints flat with no supports needed

8 days agoRemix →

Burrito de Calibración Ajustado

Un problema típico de los modelos de calibración es que las proporciones no siempre evalúan bien lo que se busca. Un cuerpo demasiado macizo oculta defectos que una cabeza grande podría revelar. Este ajuste reduce el volumen central, dejando la cabeza como la masa principal. Dimensiones de prueba Cuerpo central: 12x16 mm Altura de inicio de cola: 9 mm Espacio entre patas: Reducido para puentes más cortos

10 days agoRemix →

1x6x6 Building Block Panel

A tall, 1x6 building block panel standing 6 standard bricks high. The part features a uniform hollow core that reduces material use while providing the correct bottom tolerances to friction-fit over standard 4.8mm studs. Specifications Footprint: 1x6 studs (48mm x 8mm) Height: 6 standard bricks (57.6mm) Top Interface: 6 standard 4.8mm studs Bottom Interface: Continuous 4.95mm friction channel Print Settings: Prints upright without supports; the 4.95mm internal roof easily bridges on standard FDM profiles.

13 days agoRemix →