Made by YoItsMe
Created 3 months ago
Remixed 2 times
Description
That perfectly aligned stripe of wet road grime the rear tire slings exactly past the bottom edge of the plate and up the center of your jacket is miserable. Tail tidies look good, but they leave the dead center of the wheel completely unshielded.
This is a wedge deflector that clips directly onto the bottom edge of the numberplate. It projects a downward-angled, 18mm shelf backwards toward the wheel, catching that specific arc of water and directing it back at the road. The ends are heavily swept to match the sharp lines of modern sport bikes like the Z-series.
Images
BeamWedge is a shallow mounting wedge for a motorcycle number-plate lamp. It tilts the lamp down toward the plate instead of into the eyes of people behind, while the 53 mm × 13 mm face matches the lamp body and keeps the profile compact. A pair of screw holes and a bevelled central cable opening let the lamp sit cleanly on a number-plate holder, and the 5.5 mm body thickness with a 3 mm thin edge keeps the wedge unobtrusive. All four corners are rounded at 3 mm radius, so no sharp points sit against the holder or the lamp body. The set also includes two 11 mm angled washers as separate parts. They sit on the back side under the screws to correct the mounting angle, with a low-profile wedge section, 4 mm centre holes, and a slope that matches the back of the wedge. Fit each washer with its thick edge on the side where the wedge is thinnest. Fit and features Slightly shallower than 15° downward tilt for aiming the lamp at the plate 53 mm wide and 13 mm tall to match the lamp body Two 5.5 mm screw holes at 39 mm centres 10 mm central cable hole with a 0.75 mm bevel on the flat back face, flaring to about 11.5 mm at the surface 5.5 mm body thickness with a 3 mm thin edge 3 mm rounded corners on all four points Two separate 11 mm angled washers with 4 mm holes, about 2.35 mm thick at the thick edge and 0.25 mm at the thin edge Print notes The wedge prints lying on its large flat back face, with the cable-hole bevel against the bed and the sloped face pointing up, so it needs no supports. The bevel leaves roughly 0.7 mm of material above and below the cable opening across the wedge's 13 mm height. That is thin but printable — run extra perimeters so the narrow bands around the hole hold up. The angled washers print flat, one face down, as separate parts, with no supports needed. Their 0.25 mm thin edge is fragile; if it prints poorly, raise it to about 0.4 mm. Before printing Check the 39 mm screw spacing and the 10 mm cable opening against the lamp before printing. The washer holes are 4 mm, which suits M4 fixings; they are tight for the wedge's 5.5 mm fixing holes, so confirm the screw size before printing.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
A single-arm servo horn for the SG90 micro servo, with a 3.2 mm linkage hole 12 mm from the output shaft centre. Fitment Fits: SG90 and compatible 9 g servos with the 21-tooth, ~4.8 mm output spline. Does not fit: MG90S metal-gear servos with a different spline count, or 25T servos such as MG995/MG996. Arm: 12 mm centre distance, 4 mm thick, rounded edges. Check before printing Test the spline bore on a scrap print. Bore size is ~4.9 mm with small tooth notches, and printer tolerance varies. Adjust it if the fit is loose or tight. The part prints flat with no supports, and PLA works.
Girante per pompa acqua Kawasaki KX125 '98, con disco posteriore pieno, mozzo centrale ribassato e 6 pale curve a spirale. Disco base Ø38,65 mm, spesso 2,2 mm Altezza totale pale 13,5 mm Mozzo Ø14 mm, alto 10,5 mm 6 pale a spirale da 64°, spesse 2,2 mm Foro albero Ø5,2 mm con smusso all'imbocco Le quote vanno verificate con un calibro sul pezzo originale prima della stampa.
What it's for 30×40 mm 底板,前端带两片独立固定耳片,用于锁 SG90 舵机自带的安装耳。 Dimensions 底板 30×40×2 mm,圆角 R1,2 个 φ2 孔,孔距 22 mm 耳片各宽 4.2 mm、厚 2 mm、高 14.5 mm 耳孔 φ2,中心距 28 mm,孔内侧距耳片内边 0.2 mm Remix ideas 加宽耳片内侧以增加强度 恢复 U 型侧壁
ServoLink is a compact single-bar crank arm for SG90 micro servos. One end carries a 21-tooth spline socket that grips the servo output shaft. The other end has a 3.2 mm round hole for a linkage pin or screw. The part is flat and printable without supports. Dimensions Hole centre to centre: 12 mm Thickness: 4 mm Left hole: SG90 spline, about 4.9 mm across the teeth Right hole: 3.2 mm diameter Hub: 9 mm round, arm end: 7 mm round, with softened edges Print notes PLA, printed flat, no supports The spline is sized close to nominal. Scale the hole slightly if your printer runs tight or loose.