Planter Solar Canopy Mast
Created 1 months ago
Description
Plants roast in direct midday sun while flat-laying solar panels waste table space and inevitably get knocked onto the floor.
This cantilevered mast bolts directly to the back of the soil basin, hoisting a 140mm square solar mounting plate squarely over the canopy. It acts as an umbrella for the soil while capturing the light that would otherwise scorch the leaves, keeping the footprint entirely vertical.
Mast Clearances
- Mast Height: 250mm from soil rim to canopy plate
- Mount Plate: 140x140mm flat surface
- Standoff Base: 40mm wide clamping surface against the basin wall
Photos
Technical views
More like this
Explore more in Home & Fixtures →
Ruined 85mm Column Planter
A functional planter designed to resemble a fragmented ancient stone column. The exterior features classical deep flutes and a stepped pedestal base, while the top rim and outer walls integrate geometric cutaways simulating heavy weathering and structural breaks. Specifications: Dimensions: 115 mm maximum base diameter, approximately 110 mm peak height. Cavity: 85 mm diameter bore with an 80 mm depth to house standard small nursery pots. Tolerances: Minimum 5 mm wall and base thickness maintained throughout all flutes and fracture geometry. Printability: Optimised for standard upright FDM printing; all destructive boolean cuts are angled to eliminate the need for supports.
Halo Drip Irrigation Ring
This is a low-profile, continuous-loop irrigation ring designed for automated watering systems. It distributes water evenly around the base of a plant without interfering with the stem. The structure is engineered specifically for FDM printing without supports. The internal hollow channel features a teardrop cross-section so the printer can bridge the ceiling cleanly, and the external hose barb includes a small, built-in support block connecting it to the build plate. Design Notes Dimensions: 197 mm outer diameter, 173 mm inner diameter, leaving a 12 mm wide profile. Inlet: Dual-barb fitting sized for 5 mm internal diameter tubing, pointing outward to keep the hose clear of the foliage. Distribution: 12 downward-facing 1 mm drip holes spaced every 30 degrees, beginning 15 degrees offset from the inlet to ensure the first drops don't pool at the connection. Mounting: Three low-profile tabs sit on the outer perimeter, drilled for standard wire pegs to anchor the ring into the soil.
Anti-Spill Armrest Caddy
Sofa arms are basically designed to launch drinks onto the rug the second you shift your weight. This drops a rigid U-channel over the armrest to bridge the gap, locking down a flat staging plate on one side and a deep cup holder into the other. Specifications Total Length: 200 mm Inner Channel Width: 185 mm (verify this clears your sofa arm) Cup Holder: 80 mm diameter, 32 mm depth Print Specs: Prints hollow to save time and material. No supports needed if your bridging is dialled in.
FlowLink Threaded Extension Pipe
A fully 3D-printable, 12-inch extension pipe designed for infinite stacking. The standard slip-fit ends have been replaced with integrated 3mm-pitch metric threads, allowing multiple segments to be screwed together securely without glue. Threaded joints: 21mm male thread with a matching 21.6mm female thread cut into the base, providing 0.6mm of clearance. Support-free design: Internal transitions use 45-degree tapers, eliminating the need for internal supports. Slim profile: Maintains a 25mm outer diameter with a robust 3mm wall.
Portavasos Anti-Charcos
Los vasos de bebida fría siempre acaban sudando y dejando un charco molesto en la mesa. Este portavasos resuelve el problema al recoger la condensación, manteniendo tu espacio seco. El diseño incorpora la silueta de una pila y texto que permite jugar con los colores de tu filamento. Medidas y Detalles Técnicos Diámetro total: 90 mm exterior. Hueco para el vaso: 84 mm (acepta tazas y vasos estándar). Impresión: Se imprime en dos partes; la base encaja a presión por debajo para revelar el segundo color a través de las letras y el contorno de la pila.
8mm Tank Bulkhead Fitting
M18 threaded bulkhead fitting engineered to pass an 8mm inner-diameter irrigation hose securely through a plastic tank lid. Interface: M18x2 thread with an independent hex locking nut. Sealing: Recessed O-ring groove on the interior flange face (2.5mm wide) to provide a watertight seal against the tank wall. Hose Barb: Double retaining barbs with a reinforced transition cone to handle clamping forces. Clearance: The hex nut is designed to slide freely over the 10.2mm barbs and internal threads are sized for clean printing in PETG. Both components are oriented to print flat on the bed without supports.