Made by NiftyBettong
Created 1 months ago
Remixed 4 times
Description
A fully mechanical, gravity-fed coin magazine tailored for standard U.S. quarters. It stores a full $10 roll vertically and dispenses exactly $1 (four quarters) per cycle into the palm of the hand. The mechanism relies on a two-stage sliding escapement, now utilizing a side-mounted limit pin to ensure the coin path remains entirely unobstructed during travel.
The main body, slider, cap, and limit pin print separately without supports. Insert the slider into the main body track, align the side slot with the right-hand hole on the body, and push the limit pin flush into the side countersink to capture the mechanism.
Images

Open-top storage box with three equal compartments side by side, and the name CHARO raised across the full front face. Outer size: 210 x 112 x 85 mm Walls and dividers: 3 mm Floor: 4 mm Compartments: 3, each about 66 x 106 mm inside Lettering: Bebas Neue, about 200 x 77 mm, raised 1 mm on the front Prints upright with no supports
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
PivotTee è un portabrugole piatto per chiavi a T da 10 a 3 mm, con perni laterali che lo fanno ruotare da orizzontale a verticale su una base da fissare al cassetto. Un fermo girevole dietro il blocco lo tiene in verticale durante l'uso, e il perno centrale accoglie un inserto filettato M3 per avvitare il fermo. Caratteristiche Otto sedi da 10 a 3 mm con fessura superiore e numeri incisi Base con due fori svasati da 5 mm Perno del fermo da 8 mm con foro da 4,2 mm per inserto M3 (profondità circa 8 mm) Fermo girevole 44 × 14 × 6 mm Print notes Tre pezzi stampati sdraiati, senza supporti Inserto filettato da scaldare a caldo nel foro del perno
flare tubintake for stove
A set of eight small label plates with raised white lettering, each 1 in × 0.5 in. Blue plates read ROAD, CURB, REAR, REAR; red plates read SCENE, DECK, TANK, TANK. Intended for marking bins, shelves, hooks or parking spots. Specs Plate: 25.4 × 12.7 mm, 2 mm thick, rounded corners, no mounting hole Lettering: 0.8 mm raised, thickened strokes, centred on each plate Layout: two columns (blue left, red right), 18 mm row spacing Print: flat on the bed, no supports; filament swap at letter height for two-tone Mounting: double-sided tape or adhesive
Loose items slide around in a drawer, and a floorless box with a divider keeps them in place. This one is a rectangular frame with no floor and a full-height wall across the middle. Key numbers Outer size: 184 x 93.33 x 115 mm (height) Wall thickness: 2.4 mm Divider: 2.4 mm, full height, at the middle of the 184 mm length Three boxes side by side fill a 280 mm drawer depth Print: open end up, no supports needed, fits beds of 210 mm or larger