Smart Duplex Sconce Plate
Created today
Description
An oversized, deep-shell wall plate for a standard US duplex outlet, built to house a Raspberry Pi Zero W and up-and-down sconce lighting.
- Pi Zero Mount: Integrated standoffs (58x23mm spacing) for M2.5 screws, tucked beside the receptacle.
- Lighting Control: 5.5mm face cutout for an ambient light sensor.
- LED Bays: Top and bottom mounting blocks with flush cutouts for dual-directional LED strips.
- Clearance: 14mm overall depth clears standard hardware while providing internal routing space.
Images
More like this
Explore more in Home & Fixtures →
30mm Fluted Drawer Knob
A mushroom-style drawer knob with a straight-fluted grip ring. Designed for environments where hands may be wet, the flutes provide mechanical grip without the complex recesses of a diamond knurl that trap moisture. The part includes a central clearance hole for standard M4 mounting screws. Specifications Cap Dimensions: 30 mm diameter, 18 mm tall Stem Dimensions: 12 mm diameter, 10 mm length Total Standoff: 28 mm Mounting: M4 clearance through-hole (4.5 mm diameter) Grip Feature: 30 vertical flutes
Płyta 18mm Nóżka Kątowa 150mm
Nóżka oporowa pod standardową płytę meblową 18 mm. Gniazdo ma 18,6 mm szerokości, co daje luz roboczy pozwalający wsunąć krawędź płyty bez rzeźbienia materiału, z pełnym prześwitem na wylot (brak ścianek czołowych). Dno kanału opada pod kątem, dając około 3 mm różnicy wysokości na 30-milimetrowym odcinku chwytu. Podstawa została rozszerzona do 45x45 mm – przy 150 mm całkowitej wysokości prosty słupek nie utrzymałby obciążeń bocznych. Wymiary montażowe Kanał U: 18,6 mm szerokości, 40 mm głębokości (w najpłytszym miejscu). Mocowanie: Dwa otwory przelotowe 4,5 mm z fazowaniem pod wkręty z łbem stożkowym, rozstaw 14 mm. Wysokość całkowita: 150 mm. Kąt dna: Spadek 3 mm na 30 mm długości profilu. Pasuje do gołych płyt 18 mm (wiórowa, MDF, sklejka). Nie wciśniesz w to płyty 22 mm, a z płytą 16 mm wkręty po obu stronach będą musiały ściągnąć ścianki kanału, co grozi pęknięciem wydruku. Przed drukiem upewnij się, że 3 mm spadek na dnie to właściwy kąt dla twojej zabudowy.
280mm Irrigation Controller Enclosure
A rigid 280 × 200 × 90 mm printed enclosure designed specifically for an ESP32-based multi-zone plant irrigation controller. The layout divides the internal volume into three distinct areas: high-current power distribution on the left, six MOSFET drivers in the center, and the low-voltage microcontroller logic on the right. An extra-wide central cable channel runs between the two rows of MOSFETs, and all high-traffic access areas—like screw terminals and adjustment dials—have generous working clearances. The outer walls feature deep U-slots for cables, cut from the top edge so the main flat lid traps them cleanly in place without relying on separate cable glands. Internal Layout details Zone A (Power): Mounts for a 56×35 mm DC-DC buck converter, a friction-fit bracket stack for four WAGO 221-415 lever connectors, and a C-clip for an inline 5A barrel fuse. Zone B (Switching): Two rows of custom mounts for six 35×32 mm MOSFET boards. Each uses exactly two diagonal standoffs to leave maximum free space around the terminals. Zone C (Control): Stand-offs for an ESP32 NodeMCU, with a dedicated USB-C opening aligned in the external right-hand wall. Structure: Embossed floor labels mark all hookup zones. Cable tie bridges are scattered throughout the base for organization, and vertical ventilation slots flank the rear and sides. Uses four M3 screws driven directly into heavy internal corner bosses to seal the lid.
9-Inch Planter Drainage Raiser
A structural insert built to elevate a 9-inch plastic nursery pot inside a decorative ceramic planter. Standing 3 inches tall, it provides a solid base while allowing standing water to drain clear of the roots. The top deck uses a concentric ring and spoke pattern — significantly stronger and faster to lay down than a square grid. The load is carried outward to four tapered pillars set directly under the main intersections. Remix Hooks Total Height: Built at 76.2 mm (3 inches), but the leg pillars can be stretched or squished to match any outer pot depth. Deck Thickness: Starts at 6 mm to handle a 20 lb load without bowing. Leg Taper: Set at 24 mm at the base narrowing to 18 mm at the top — widen the base if you need it to sit on a softer medium instead of a hard ceramic bottom.
Brutalist Pipe Insert
A heavy-duty ventilation insert featuring an integrated square mesh. The single-ended flange acts as a firm stopping collar, while the dense internal grid blocks debris and insect ingress without severely choking airflow. Designed as a drop-in piece for 80 mm bulkheads or exhaust pipes. Design Notes Mesh: 3x3 mm openings with 1.5 mm solid bars Interface: 80 mm main outer diameter with a 2 mm wall Collar: 5 mm thick flange to prevent over-insertion Printability: Single solid body, optimized for FDM without supports
