Squared Inner Handle Bezel
Created 2 months ago
Description
A replacement inner door handle bezel for automotive applications, built with an extended flange and a squared-off recess contour. Incorporates a large-radius relief curve to sit flush against padded door cards.
What it's for
Replaces cracked or missing interior handle surrounds. Features reinforced retention clips and thick mounting walls to handle tension without shearing.
Dimensions
- Total Outer Area: 153 mm × 81 mm
- Recess Depth: 24 mm
- Lever Cutout: 49 mm × 54 mm
Print notes
Standard rigid plastics like ABS, ASA, or PETG are recommended for automotive interiors to handle high cabin temperatures. Print flat on the front face (flush rim) for optimal layer orientation on the snap clips.
Images
More like this
Explore more in Automotive, RC & Hobby →
86x45mm Ovaler Karosserie-Blindstopfen mit Snap-Fit-Clips
Geschlossene ovale Abdeckplatte für eine 80 × 39 mm große Öffnung in etwa 1 mm dickem Karosserieblech. Die Kontur ist ein Stadion-Oval, also ein gerades Mittelstück mit vollständig runden Enden. Die Platte wird eingedrückt, die integrierten Snap-Fit-Clips federn zurück und rasten hinter dem Blech ein – ohne Schrauben, Kleber oder separate Befestigungsteile. Die Abdeckung lässt sich wieder entfernen, ohne das Blech zu beschädigen. Das Teil wird als ein Stück gedruckt. Frontplatte: 86 × 45 mm, 2 mm dick, vollständig geschlossen, gerundete Kanten; die 2 mm fallen an der gerundeten Kante etwas dünner aus Einsatz: Außenkante 80 × 39 mm, Endradius 19,5 mm, 4 mm tief, hohle Wand mit 1,6 mm Stärke Innenöffnung: 76,8 × 35,8 mm Flansch: rundum 3 mm breit, an den Längsseiten wie an den Enden; die Clip-Haken liegen vollständig innerhalb der Plattenfläche Clips: zwei Zungen an den Längsseiten oben und unten, je ein 0,7 mm hoher Haken mit Rampen-Anlauf und flacher Fangfläche für 1 mm Blech Clip-Schlitze: 1 mm breit × 6 mm lang durch die Wand der Längsseiten, geben den Zungen Platz zum Federn Passung: Die Außenkante des Einsatzes entspricht exakt 80 × 39 mm, es bleibt kein Spiel – straffer Sitz, vor dem Einbau einen Probedruck einplanen Einbauraum: Die Frontplatte misst 86 × 45 mm; vor dem Einbau prüfen, ob um die Öffnung herum genug Platz für 45 mm Höhe ist Material: PETG oder ASA, mit der Frontseite nach unten drucken Bauteilmaße auf der Druckplatte: 86 × 45 × 6 mm
Push-In Trim Clip, Screwable Head
A dashboard-trim style push-in clip with a smooth, fully closed 22 x 16 mm rounded head and a solid central core that takes a self-tapping screw from the front. Head: 22 x 16 x 3 mm, rounded corners, no holes Shaft: 10 x 10 mm, about 18 mm long, chamfered insertion tip Two spring arms with tapered ramps and locking shoulders, 13.5 mm across the barbs Narrow slots separate the arms from the central screw core Best printed in PETG or ASA
Oo scale buildings half relief roof with ridge tiles
Two tiled OO-scale roof slopes, two slated roof slopes, five brick chimneys and a downpipe, all laid out to fit a 256 × 256 mm bed in one plate. Remix hooks Layout: the four roofs sit side by side along X, with chimneys and the downpipe in the strip on the right. The whole set spans about 240 × 156 mm. Tiled roofs: 46 × 156 mm slab, 3 mm thick, 4.5 mm radius ridge tile wrapping 135°, half-round gutter with 2 mm opening and 0.8 mm walls, closed ends and a 2 mm outflow hole. Slated roofs: 46 × 130 mm, 30° pitch, 2.5 mm courses, 7 mm slates, no gutter. Chimneys: 7 × 7 mm, 16 mm tall, base cut at 30°, printed upside down. Change the height or the cut angle for other roofs. Downpipe: 2 mm × 110 mm solid rod. Lengthen it or add brackets. Pairs well with a printed wall or building shell that matches the 30° and 45° pitches.
Gancho de Garrafa com Braçadeira Snap
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
Wall-Mounted Jack Stand Hanger small support
A wall-mounted holder that keeps a 3-ton jack stand off the garage floor and within reach. The flat vertical back plate carries a U-shaped cradle in the centre, open at the top so the stand's bar drops in and lifts out. The cradle is open through the middle and closed by a 10 mm wall at each end, so the bar cannot slide sideways off the holder. The front wall of the cradle is a 13 mm lip that catches the bar and stops it sliding forward. The cradle walls are rounded with a 7 mm radius on every edge except the one against the back plate, and the inner floor is a rounded half-cylinder trough running the length of the opening, 28 mm across to match the seat, so a round bar or handle lies in it without rocking. The holder prints as one piece with no assembly, and it is sized for a 3-ton jack stand and its handle. A compact gusset supports the cradle underneath and runs the full 100 mm width of the cradle, so the end walls sit flush on it instead of overhanging. Its corners carry the same 7 mm radius as the cradle, so the walls run down into it with no ledge. The underside is an S-curve: it leaves the back plate 39 mm up, sweeps out and finishes running straight up the back of the front lip, meeting both surfaces tangentially so there is no crease where it joins. Keep it around this size — trimming it much further leaves the cradle with little support against the weight of a loaded stand. The jack handle hangs from two cuts, so it drops in from above rather than being threaded in from the front. A 28 mm slit in the front wall, open at the top, sits 24 mm right of centre and stays clear of the right edge, which runs fully to the front and stands even with the left wall. Opposite it, the left end wall carries a matching 28 mm notch, open at the top. Both cuts share the cradle trough's floor depth, with their centreline at 80 mm up and their floors bottoming out at 66 mm. The slit floor starts at the trough centreline with a rounded blend where the two meet, so the handle slides from the trough into the slit and notch without a step and hangs clear below. The cradle walls stand 55 mm tall, topping out at 110 mm up, which leaves about 16 mm of wall above a 28 mm handle resting at 80 mm. Overall: 100 mm wide, 130 mm tall, 57 mm deep Cradle: U-shaped, 28 mm bar seat, open top, open through the middle, 10 mm end wall each side, rounded floor trough Cradle walls: 55 mm tall, tops at 110 mm, rounded at 7 mm Bar opening: about 80 mm between end walls Front lip: 13 mm thick Handle slit: 28 mm, open at the top, set 24 mm right of centre in the front wall, floor blended into the trough Left end wall: matching 28 mm notch, open at the top, for the other side of the handle Floor height: slit, notch and trough all bottom out at 66 mm Gusset: full cradle width, 7 mm rounded corners, S-curve underside tangent to the back plate and the front lip, meeting the plate 39 mm up Mounting: one countersunk screw hole above the cradle and one below; use 5 mm or larger screws into a stud or suitable anchor Material: grey PETG suits the load and garage conditions; edges are chamfered Check that the stand's bar fits the 28 mm seat and the 80 mm opening, and that the handle fits the 28 mm slit and notch before printing. If the bar or handle is larger, widen the seat or the cuts to match.
Elliptical Pedal Center Insert
A 48 × 40 × 7 mm replacement insert for the broken center of an elliptical trainer pedal. Flat top, 10 mm through-hole, 20 mm full-height boss, and a ribbed underside. Remix hooks Footprint (48 × 40 mm): the main value to tune to the pedal pocket; rim, ribs and diagonals follow it. Top edge chamfer (0.5 mm): set to 0 for a fully tight seam. Hole (10 mm) and boss (20 mm): change for a different axle or bolt; a wider boss adds strength. Underside depth (3 mm): rim and ribs can be taller or thinner, with the top plate at 4 mm. Pairs with: countersunk screws or adhesive through the boss area.