Stackhouse — OO Scale Brick Chimney
Created today
Description
Stackhouse is a tapered, square industrial chimney at OO scale, about 200 mm tall, built from four brick-faced side panels plus a separate base and cap. Each of the base and cap carries a raised, tapered spigot that the panels slide over, so the four sides locate themselves during assembly.
The panel edges are cut at the true mitre for the taper rather than a flat 45°, so adjacent faces meet cleanly along the corner lines.
Features
- Four identical panels, printed flat with the brick face up
- Edges cut to the exact mitre angle for the taper
- Base plinth with a tapered spigot rising inside the panels
- Cap with a chamfered overhang and a downward spigot
- 0.3 mm clearance between spigots and panel interiors
Dimensions
- Height: 200 mm of panel
- Outer width: 40 mm at the base tapering to 24 mm at the top
- Wall: 3.4 mm including 0.4 mm brick relief
- Spigot depth: 12 mm
- Base plinth: 54 × 54 × 6 mm; cap: 38 × 38 × 5 mm
Print notes
- Brick courses are oversized for a 0.4 mm nozzle.
- Panels are long; angle them diagonally if the bed is short.
- Glue panels to each other and to the spigots.
Images
More like this
Explore more in Decor & Display →
OO Scale Arched Door Frame 13x26mm
Arched door frame and separate door for an OO scale (1:76) house, sized for a 13 x 26 mm wall opening with a semicircular top. The frame is 2 mm deep and continues around the inside of the arch, leaving a semicircular glass gap above the door. Frame: 12.8 mm wide, 25.9 mm tall, 2 mm deep Glass gap: semicircle, 8.8 mm across Door: 8.4 x 17.8 mm, printed as a separate piece Door detail: four raised panels, round handle, letterbox plate Fit: 0.1 mm clearance per side in the wall opening Print with a fine layer height; panel relief is 0.4 mm
16 mm Arched Door Frames and 15x20 Windows Set
Six arched door-and-frame pieces and twelve rectangular windows for an OO scale (1:76) house, laid out flat on the plate. What it fits Door frames: 16 mm wide, 2 mm deep, with a semicircular arch top. Each has a door printed in one piece with it. Windows: 15 x 20 mm, 1.6 mm deep, with a transom bar across the middle. Check before printing Measure the wall openings against the 16 mm frame width and 15 x 20 mm window size. The door relief is 0.4 mm, so use a fine layer height. Not covered The windows are not arched and have no glass pane. Sizes are not matched to any other scale.
Blank-Sign Mandarin Storybook Town
A tabletop storybook town in the spirit of a classroom diorama: four pastel buildings along a back row, a road with parked cars, and a park with banners, people, trees and benches. Every sign and banner is left blank, ready for hand lettering with paint pens or stickers. Where each word goes 医院, 图书馆, 商店, 社区中心: white plaques on the four building fronts (hospital has a red cross) 工作: small plaque on the shop 服务: orange banner in front of the library, with people nearby 公园: green banner at the park 活动, 一起, 参加: banners above groups of people 社区: blue banner near the road Extra features Road, path, trees, people, benches, cars and streetlights
Street Lamp Base with Domed Foot
A miniature street lamp base for a 1:64 diorama. A domed foot with a flat 7.2 mm bottom rises into a straight 5.5 mm shaft, 10 mm tall overall, with a centred 2 mm through-hole. Height: 10 mm Shaft diameter: 5.5 mm Foot diameter at the flat bottom: 7.2 mm Dome height: 6 mm Through-hole: 2 mm, fully open One solid body with a flat bottom, no decoration
Small City Model with Park and Trees
A 230 × 170 mm town plate laid out as a small city: a row of five tall buildings along the back, a main road with crosswalk, side buildings, houses, cars, streetlights and a park with a pond, crossing paths, a bench, people and many trees. All lettering has been removed. Base: 230 × 170 × 4 mm plate Park: lawn, pond, two crossing paths, 19 trees, bench City: buildings 14–34 mm tall with windows and doors Extras: streetlights, cars, people, crosswalk Print: no supports needed for most parts; trees are cones and print best with a slow top layer
Funfair Swing Ride with Crank, 100 mm Base
Funfair swing ride with a hand crank on top. Turning the crank spins the canopy and seat ring around a fixed central pin, and each of the six seats hangs from a captive ball joint so it swings outward as the ride turns. Base: 100 x 100 x 6 mm plate with a 30 mm column and 14 mm mast Spinning top: 70 mm seat ring and cone canopy on a 8 mm pin, 0.3 mm bearing clearance Seats: six, each on a 7 mm captive ball with a 3 mm rod, printed in place Crank: 30 mm arm with a 7 mm handle on top of the canopy Print in place, no supports needed for the base; the ring cavities bridge over the balls Overall height about 112 mm