Small City Model with Park and Trees
Created today
Description
A 230 × 170 mm town plate laid out as a small city: a row of five tall buildings along the back, a main road with crosswalk, side buildings, houses, cars, streetlights and a park with a pond, crossing paths, a bench, people and many trees. All lettering has been removed.
- Base: 230 × 170 × 4 mm plate
- Park: lawn, pond, two crossing paths, 19 trees, bench
- City: buildings 14–34 mm tall with windows and doors
- Extras: streetlights, cars, people, crosswalk
- Print: no supports needed for most parts; trees are cones and print best with a slow top layer
Images
More like this
Explore more in Decor & Display →
Wickiup — Domed Hut Miniature
Wickiup is a small domed hut miniature inspired by the Apache wickiup shown in the linked reference image. A hollow dome with an arched doorway and a roof smoke hole, wrapped in raised bands that suggest woven thatch. Features Hollow dome, about 60 mm wide and 30 mm tall Arched doorway facing the front Smoke hole at the top Raised thatch bands in a second colour Print notes Flat base, so it prints without a raft Door arch is small; supports are rarely needed
wigwam
Scale model of a wigwam-style domed hut on an 88 mm round base, with an arched front doorway, a top smoke hole, three binding bands and hay thatch strands angled down the dome. Fit and dimensions Base disc: 88 mm diameter, 2 mm thick Dome: about 80 mm wide, roughly 32 mm tall overall Doorway faces -Y; thatch is left clear of it Check before printing Hay strands are about 1 mm thick. Use a 0.4 mm nozzle and expect fine, fragile detail. Not a functional enclosure, and not scaled to fit any figure or miniature line.
model saat
A slim protective sleeve for the SIBIONICS SiWatch with its own reinforced strap lugs, so strap load bypasses the broken originals. The screen, back sensors and charging contacts stay open, and two separate button openings sit on one side edge. Remix hooks button1offset / button2offset: Y position of each opening along the side, measured from the watch centre. Starting values are -5 mm and +5 mm. Each moves independently. btnz, btnlen, btn_h: opening height above the back (5.5 mm), length (6 mm) and height (3.5 mm). btn_side: 1 for the +X edge, -1 for -X. Cavity: watchw 38, watchl 44, watchh 11 and cornerr 9 mm are placeholders to measure. Strap: strapw 22, bard 3, barz 6.5 and bary 1.5 mm. Pairs well with a test-fit print in cheap filament before the final one.
Cross Arm Traffic Light Pole Model
A miniature traffic light pole with a horizontal cross arm, built as a single-piece STEM teaching model. A hexagonal base keeps the 90 mm round pole upright. The 45 mm arm carries a slide-in holder at its end for a 52 × 22 mm traffic light PCB module. Pole: 12 mm diameter, 90 mm tall, on a 44 mm hexagon base Arm: 45 mm from the pole axis, with a 45° brace underneath so it prints without support Holder: 2.2 mm walls, edge lips, and a top stop. The board slides in from below Rear clearance: 6 mm gap behind the board, open on the cable side for the 5-pin connector Board fit: assumes 1.6 mm thickness with 0.2 mm play per side Prints upright in PLA as one piece.
Moonlit Ghost Chain Swing Display
A friendly sheet-wearing ghost sits on a chain swing hanging from the horn of a crescent moon, in the spirit of a Halloween nursery rhyme. His blue tennis shoes dangle below the sheet and his hands grip the chains above his head, the way a kid holds on mid-swing. Crescent moon with shallow craters Chain swing with a rounded seat Cut-out eyes and a recessed smile Flat rounded base keeps the whole scene standing upright Sand the edges before handing it to a child.
Christmas Tree Lantern for LED Tealight
A Christmas tree lantern that sits over a battery LED tealight, so the light stays hidden inside instead of glaring from a bare tealight on the table. The walls are perforated with rings of small round holes that throw dots of light, and the bottom is open so the LED can be placed or swapped without taking anything apart. Key numbers Height: about 135 mm including star Base diameter: 90 mm, open underneath (inner opening about 87 mm) Wall: 1.6 mm, three stacked tiers Perforations: 4.2 mm holes, staggered rings Star: separate colour, peg-mounted into the top tier Printing Print upright, open end down, no supports needed for the cone walls Green for the tree, gold or yellow for the star Use a 0.4 mm nozzle; a lighter or translucent filament glows more