Stemmed Goblet With Flowers and Vines, 125 mm
Created today
Description
Clear drinking goblet, 125 mm tall with an 80 mm rim and a 56 mm round foot. Ten raised five-petal flowers sit around the outside of the bowl, each with a vine stem that runs down the bowl wall. Five of the vines continue and spiral down the stem toward the foot.
- Flowers and vines are on the outside only; the inside stays smooth
- Vine thickness: about 2.2 mm, raised from the surface
- Five vines wind down the stem; the other five end at the base of the bowl
- Material: clear PETG suggested
- Supports: likely needed under the bowl flare
Photos
Technical views
More like this
Explore more in Decor & Display →
2
A conical vase, 150 mm across the base, 200 mm across the top and 300 mm tall, with 10 mm walls and floor. Maple leaves cover the outside in staggered rows, 9 rows of 16. Remix hooks Leaf density: 16 leaves per row and 9 rows at 30 mm spacing. Fewer, larger leaves give a bolder look. Wall thickness: 10 mm. Drop it to 3–4 mm to save material, or keep it thick for stability. Taper: base radius 75 mm, top radius 100 mm. Swap them for a flared-in neck. Leaf relief: 3 mm deep. Use less for a subtle texture. Pairs with: a glass jar liner for fresh flowers, since the walls are not waterproofed by the print itself.
model saat
A slim protective sleeve for the SIBIONICS SiWatch with its own reinforced strap lugs, so strap load bypasses the broken originals. The screen, back sensors and charging contacts stay open, and two separate button openings sit on one side edge. Remix hooks button1offset / button2offset: Y position of each opening along the side, measured from the watch centre. Starting values are -5 mm and +5 mm. Each moves independently. btnz, btnlen, btn_h: opening height above the back (5.5 mm), length (6 mm) and height (3.5 mm). btn_side: 1 for the +X edge, -1 for -X. Cavity: watchw 38, watchl 44, watchh 11 and cornerr 9 mm are placeholders to measure. Strap: strapw 22, bard 3, barz 6.5 and bary 1.5 mm. Pairs well with a test-fit print in cheap filament before the final one.
Soporte de tarjetas con estrella grabada
Bloque rectangular con una ranura central para tarjetas y una estrella de cuatro puntas con lados curvos, grabada hacia el interior de la cara frontal. Bloque de 115 x 25 x 20 mm con bordes achaflanados Ranura de 4 mm de ancho y 10 mm de profundidad, de extremo a extremo Estrella curva de 16 mm de punta a punta, hundida 1,5 mm y centrada en la cara frontal Se imprime sin soportes apoyada sobre su base
Moonlit Ghost Chain Swing Display
A friendly sheet-wearing ghost sits on a chain swing hanging from the horn of a crescent moon, in the spirit of a Halloween nursery rhyme. His blue tennis shoes dangle below the sheet and his hands grip the chains above his head, the way a kid holds on mid-swing. Crescent moon with shallow craters Chain swing with a rounded seat Cut-out eyes and a recessed smile Flat rounded base keeps the whole scene standing upright Sand the edges before handing it to a child.
OO Scale Arched Door Frame 13x26mm
Arched door frame and separate door for an OO scale (1:76) house, sized for a 13 x 26 mm wall opening with a semicircular top. The frame is 2 mm deep and continues around the inside of the arch, leaving a semicircular glass gap above the door. Frame: 12.8 mm wide, 25.9 mm tall, 2 mm deep Glass gap: semicircle, 8.8 mm across Door: 8.4 x 17.8 mm, printed as a separate piece Door detail: four raised panels, round handle, letterbox plate Fit: 0.1 mm clearance per side in the wall opening Print with a fine layer height; panel relief is 0.4 mm
Placa Retangular com Borda Dourada e Texto
Placa retangular de 95 x 40 mm e 2 mm de espessura, com uma margem dourada fina recuada da beirada e a frase "Obrigado ao Cb PM Gabriel do Sd BM Luís Gustavo" em relevo, em duas linhas. Placa: 95 x 40 x 2 mm Margem dourada: 1 mm de largura, recuada 3 mm da beirada, 1 mm acima da superfície Texto: em relevo de 1 mm, centralizado dentro da margem Pensada para impressão multicolor ou pintura posterior