Stepped Quick-Access Card Wallet
Created 3 months ago
Description
A minimally-sized, rigid wallet designed to hold exactly six standard credit cards, featuring a dual-stage thumb slot. The bottom track allows the entire stack to be pushed up simultaneously, while the extended top track catches only the front card, letting it ride further out for immediate access.
What it's for
Designed for everyday carry where quick access to a primary card is essential, without sacrificing the dense, low-profile footprint of a hard-shell case.
Dimensions
- Outer Shell: 59mm x 88.5mm x 10mm
- Internal Pocket: 55mm x 87.25mm x 6mm (sized for a stack of six standard 0.76mm-thick cards)
- Primary Ejection Track: 25mm deep
- Secondary (Front) Track: 50mm deep
Remix ideas
- Add a rear money clip or elastic band anchor for carrying cash.
- Aggressively fillet the outer Y-axis edges for a smoother feel in tighter pockets.
- Add a minor interior retaining lip at the top edge to increase friction on the cards.
Images
More like this
Explore more in Keychains & EDC →
Staircase Slim Card Wallet
A card wallet with the silhouette of a tiny amphitheatre: six standard cards sit in a tall open pocket, and the floor climbs toward the front in 1.5 mm steps so the front card rides highest. A rounded thumb cutout in the front wall lets you push the stack up and out, and the front card pops clear of the rest for a quick grab. The pocket is sized for standard credit cards (85.6 x 54 x 0.76 mm) with a little breathing room, in a slim 90.5 x 10 x 58 mm body. The stepped floor is a separate colour region in the preview so the staircase is easy to read. Design notes Pocket: 86.5 x 55 x 6 mm, open at the top Floor: six steps, each 1.5 mm higher than the one behind, so the front card sits about 7.5 mm above the back one Thumb cutout: round-bottomed notch through the front wall, 36 mm wide Vertical corners rounded at 1.5 mm for a comfortable pocket feel Prints upright or flat; no supports are needed for the main body Remix hooks Taller or shorter steps for a different stagger A narrower thumb notch for a stiffer front wall Fewer steps and a thinner pocket for a 3 or 4 card version
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
Bharat Key — Mini Number Plate Keychain
Bharat Key is a miniature Indian-style number plate keychain made to carry the exact registration PB 65 BK 3388. The long, slim plate uses a light grey/white base, a thin raised black border, and bold black lettering raised on one horizontal line. The single keyring hole sits at the extreme left with a raised ring around it for strength, while the registration stays centred in the remaining space. No blue IND strip, flag, extra colour or decoration is present, so the tag keeps a clean plate look while staying sturdy enough for a keyring. Dimensions Plate: 75 × 20 × 2.5 mm Raised border and text: 0.6 mm above the base; border 1 mm wide Lettering block: about 57 × 11 mm, fitted to the space right of the hole Keyring hole: 4 mm diameter, cut fully through at the extreme left Hole ring: raised black ring around the hole for extra strength Features Exact registration text: PB 65 BK 3388 on one horizontal line Bold black lettering raised above a light grey/white base Thin raised black border around the whole plate One circular keyring hole at the extreme left, fully through the plate Raised black ring around the hole to reinforce the keyring area Flat rectangular body with slightly rounded corners and a smooth flat backside Light grey/white base and black details only — no blue, no flag, no logos or decorations Print notes Print flat on the back; no supports are needed. The raised border and lettering sit 0.6 mm above the base and read clearly at miniature scale. Keep the 4 mm hole clear so the plate hangs cleanly on a keyring.
Number Plate Keychain with 4 mm Keyring Hole
A flat 65 × 17 mm number plate keychain built around the three things that ruin a printed tag: a hole that tears out, lettering that runs off the right edge of the plate, and a border crowded with extra frames. The hole sits inside a raised black ring instead of hanging on a thin web of plastic, so a heavy bunch of keys has something solid to pull against. The registration line sits on one horizontal line, raised 0.6 mm so it stays readable instead of rubbing smooth in a week, and it starts clear of the ring so nothing touches the hole. Print and fit Plate: 65 × 17 × 2.5 mm, corners rounded, smooth flat back. Keyring hole: one 4 mm through-hole at the far left, 7 mm in from the end so its ring clears the border, fully open through the base, with its own clear area so it never meets the text. Hole ring: a 9 mm black raised ring around the hole, kept neat and with no other decoration around it. Lettering: "PB 27 F 9146" on one line, raised 0.6 mm in a heavy bold face with even spacing, sized to fit the space between the ring and the right border. Border: a single thin black raised border around the whole plate, 0.6 mm high — no inner frame. Base: light grey, flat and unbroken underneath, prints without supports; the detail all sits on the raised top face, so a two-colour print or a paint fill both work. The text sits a little right of the plate's true centre because the hole takes up the left end — a truly centred line would run into the ring. If you change the registration, shorten the text rather than the plate, or the line will overrun the border on the right side.
SPD-SL Cleat Covers With Wet-Tile Tread
SPD-SL cleat covers for walking in cycling shoes without clacking across café floors or skating on wet tile. Bare cleats are hard plastic on a hard surface, so they click, slide, and wear down. This cover wraps the cleat and puts a deep cross-hatched tread between the cleat and the floor. The outline is a rounded teardrop, widest at the heel end. It approximates the triangular cleat footprint and has no retention lip, so it relies on a snug fit. Print one and test it on a cleat before printing the pair. Numbers that decide fit and print Cleat footprint allowed for: about 75 mm long by 55 mm wide at the heel end Clearance around the cleat: 0.3 mm per side Side wall: 3 mm Sole thickness: 6 mm, with the cavity above it Overall height: 16 mm Overall size: about 81 mm long by 61 mm wide Tread: diagonal cross-hatch grooves at ±45°, 2.5 mm wide and 3 mm deep, on a 7 mm pitch Material: TPU gives the best grip and a flexible fit. PETG also works. Orientation: print sole-side down. The cavity opens upward, so no supports are needed.