Stickpot
Created today
Description
A screw-top tackle jar in the spirit of a carp angler's bankstick kit: tall bore, flat slotted tabs at the base, and a half-circle arch standing on the lid for hanging rigs.
Design notes
- 30 mm bore, 100 mm tall
- Bankstick clip now runs from the base of the jar upward, 50 mm long, with a snap-in slot
- Three flat slotted loops at the base, printing flat with no overhang
- Lid with a 6 mm wide half-circle arch, printed upside-down beside the jar
Images
More like this
Explore more in Storage & Organization →
RigPot — Bankstick Jar with Rig Loops
RigPot is a 30 mm bore, 100 mm tall screw-top jar built for carp tackle. It has a 50 mm side clip for a 15 mm bankstick, and three half-round loops for hanging rigs. Features 30 mm inside diameter, 100 mm tall Screw lid printed separately beside the jar Bankstick clip, 50 mm long, 15.4 mm bore with a snap-in slot Three flat half-ring rig loops at 90°, 180° and 270°, both ends fused into the jar wall Print notes The jar, clip and loops print as one body The lid is a separate piece and prints beside the jar
Clara Key 01
A flat, key-shaped keychain with "Clara" raised on the blade in a marker-style hand. The round bow carries a 5.5 mm ring hole, and the tip has a few simple teeth cut into the lower edge. Remix hooks Name: swap "Clara" for any other name. The lettering is scaled to a 46 mm width, so longer names get shorter letters. Widen the blade past 82 mm if you want them to stay tall. Thickness: the plate is 3 mm with 1.2 mm raised text. For a two-colour print, pause at layer 3 mm and swap filament. Bow: 32 mm diameter. Shrink it for a slimmer fob, or enlarge it and add a second hole. Teeth: three 4.5 mm notches plus a tip notch. Change the spacing or depth for a different silhouette. Pairs with: a split ring, a small lobster clasp, or a matching set with other names. Prints flat with no supports. The overall length is about 96 mm.
Esquinero en L 20 mm
Para qué sirve Esquinero en L para sujetar la esquina de un taco de hojas de hasta 4 mm de espesor. Las esquinas redondeadas lo hacen más suave al tacto y evitan puntas. Se imprime en dos mitades planas que se encajan y se pegan para formar la pieza completa. Dimensiones Brazos: 20 × 20 mm Ranura: 4,6 mm (4 mm de papel + 0,6 mm de holgura) Paredes: 1,6 mm Banda entre la esquina interior y la exterior: 6 mm Alto total montado: 7,8 mm (mitad inferior 4,7 mm, mitad superior 3,9 mm) Esquinas exteriores redondeadas con radio de 4 mm Encastre: cresta de 0,8 × 0,8 mm en la mitad inferior y ranura con 0,2 mm de holgura por lado en la superior Impresión y montaje Las dos mitades se imprimen planas y sin soportes; en la mitad superior la cara de pegado queda hacia arriba. La cresta recorre toda la pared en L de la mitad inferior y encaja en la ranura de la superior, de modo que las mitades quedan alineadas y rectas. La superficie de pegado es estrecha, porque la ranura de las hojas ocupa casi todo el centro. Conviene un pegamento que rellene bien, como cianoacrilato en gel o epoxi. Ideas de remix Cambiar el largo de los brazos para hojas más grandes. Ajustar la ranura según el espesor del taco. Añadir un agujero para atornillarlo a una superficie.
ORBISVENTILATION
Botvent is a plain, tall rectangular holder for a 9V battery, with rows of horizontal vent slots that give it a machine-panel look. No base plate, no add-on parts: just a clean open-top shell. Features Open-top box, 27.2 × 18.2 mm cavity 2.4 mm walls and floor Six horizontal vent slots on each face Square edges, 40 mm tall Print notes Prints upright with no supports needed for the slots at typical settings.
220x140x120 mm Square-Bar Storage Frame
Rectangular storage stand made entirely of solid 15 × 15 mm square bars. Two rectangular frames, top and bottom, are joined by four corner posts. A single reinforcing beam runs across the width at the middle of the top frame. All edges are sharp and all faces are flat, with no fillets or curved surfaces. Outer size: 220 mm long × 140 mm wide × 120 mm high Bar section: 15 × 15 mm, solid Posts: four, at the corners, 90 mm visible length between frames Top beam: 15 mm, centred along the length and spanning the width Print: flat bottom face on the bed, no supports needed for the main frame; the top beam spans 110 mm, so expect minor bridging sag Single welded body, symmetrical about both vertical centre planes
Spanline — Three-Part Bookshelf Riser
Spanline is a bridge-shaped bookshelf riser, 450 × 125 × 125 mm when assembled, split into three sections that each fit a 200 mm print bed. Sliding dovetail joints lock the sections together, and the tunnel underneath stays open for storage. Print layout Three separate pieces, spaced 20 mm apart, none touching. Each piece is flipped so the flat top face sits on the bed, so no supports are needed for the arch. Each piece is about 162 mm long, including its dovetail tongue. Features 16 mm top and walls with a 25 mm rounded inner arch Dovetail tongue-and-groove joints with 0.25 mm clearance Shallow rib under the top of each section Assembly Slide Part B onto Part A's tongue from the side, then slide Part C onto Part B's tongue.