Created 17 days ago
Description
Rectangular storage stand made entirely of solid 15 × 15 mm square bars. Two rectangular frames, top and bottom, are joined by four corner posts. A single reinforcing beam runs across the width at the middle of the top frame. All edges are sharp and all faces are flat, with no fillets or curved surfaces.
Images
Conjunto de dos piezas para las esquinas de una caja de controladora DJ: un soporte superior de 18 mm de diámetro que se fija al fondo de la caja y una pata inferior que se desliza dentro con 5 mm de recorrido. Se imprime en PETG, sin muelles, tornillos ni roscas. Especificaciones Soporte superior: Ø18 mm, altura 11 mm, base superior plana de 1,5 mm para pegar. Pata inferior: Ø10 mm de vástago, cabeza Ø11,8 mm, altura 10 mm, base plana para goma antideslizante. Holgura: 0,25 mm por lado (parámetro tol, ajustable según impresora). Guías: 3 nervios interiores que limitan el juego lateral. Retención: anillo tope de 1,5 mm; la cabeza de la pata, con ranuras en cruz, encaja a presión por abajo. Recorrido: 5 mm. Imprimir 4 conjuntos. La pieza superior se imprime con la base plana sobre la cama; la pata con la base hacia abajo.
Letrero con el texto "Arecson Dj" en relieve sobre una base rectangular plana de 2 mm. Pensado como placa o rótulo sencillo para un puesto de DJ, con letras en Montserrat fáciles de leer. Dimensiones Base: 90 × 24 × 2 mm Letras: 4 mm de relieve sobre la base Tipografía: Montserrat, tamaño 13 Notas de impresión Imprime plano, sin soportes. Las letras pueden hacerse de otro color cambiando de filamento en la capa 2 mm.
A 380 mm wall holder for a PS5 and a Switch Pro controller is too wide for most print beds, and a single plate can crack along its length. This version prints as two 190 mm halves that lock together with two butterfly keys. Fit and print Split line: centre of the plate, through the Yu-Gi-Oh! ring emblem Keys: two butterfly-shaped keys, 24 mm wide and 20 mm tall, 2.9 mm thick, printed flat Key pockets: cut 3.3 mm deep into the back face, 0.3 mm clearance all round Assembly: press the keys into the back pockets across the seam, then screw the halves to the wall. The wall holds the keys in Mounting: eight countersunk screw holes in total, four per half Printing: halves lie on their backs or stand on the shelf base. No supports are needed for the hollow blocks Pocket sizes are 166 mm wide and 70 mm deep, from typical controller sizes and not from measurements of a specific controller.
A tall back plate that hangs from a key rack and holds five keys on alternating left and right pegs, so fobs dangle without touching each other. The plate is 46.2 mm wide, 240 mm tall and 12 mm thick, with a 12 mm hang hole at the top right. Each peg is 8 mm in diameter, runs straight for 12 mm, then curves upward through 75° to keep rings seated. Remix hooks Plate thickness (12 mm): the easiest stiffness lever. Pegs are set into the plate face, so going thicker needs no other changes. Peg spacing (42 mm pitch): raise it for longer fobs, lower it to fit more pegs on a shorter plate. Bend angle (75°) and straight run (12 mm): lengthen the run for larger rings, ease the angle for a flatter peg. Hang hole (12 mm): resize to match your rack hook. Pairs with: any horizontal key rack with a post or screw head that fits the hole.
A matched set of eight small label plates with bold raised white lettering, styled like the enamel signage screwed to a garage wall, a shelf edge or the front of a storage bin. Each plate carries a single word — the four blue plates read ROAD, CURB, REAR and REAR, and the four red plates read SCENE, DECK, TANK and TANK — so a wall of bins, hooks, shelves or parking spots can be told apart at a glance. Colour does the sorting: blue for one group, red for the other, both with the same white lettering, so the two families stay distinguishable from across the room while reading as one set. The letters are thickened rather than enlarged, so the strokes carry weight without changing the plate size. The plates are plain rectangles with rounded corners and no fixing hole, leaving the full face free for the text — stick them on with double-sided tape or adhesive, or drill and screw them wherever they are needed. Dimensions Each plate: 1.5 in wide × 1 in tall (38.1 × 25.4 mm), 2 mm thick Rounded corners, no hanging hole Raised lettering: 0.8 mm proud of the face, strokes thickened for a heavier face Lettering centred horizontally and vertically on every plate Plates laid out 32 mm apart in two columns, blue set on the left, red set on the right Set contents Blue: ROAD, CURB, REAR, REAR Red: SCENE, DECK, TANK, TANK Print notes All eight plates sit flat on the bed and print without supports A single filament swap at letter height produces the two-tone face; painting the raised text works just as well The whole set prints in one go and comes off as eight separate tags The same layout takes any short word you want to swap in, as long as the plate size and the two-tone face stay the same.
What it's for A hinged tackle box for bass fishing gear, with a locking front latch, removable thick dividers and a leaping bass on the lid with SMITH FISHING lettering. Dimensions Base: 240 × 160 × 50 mm, 4 mm walls, 3 mm floor Lid: 240 × 160 × 22 mm with raised artwork Dividers: 5 pieces, 2.6 mm thick, sliding in 3.2 mm grooves Hinge: 5 knuckles with a separate 4.2 mm pin Latches: 2 front latches with pivot pins Remix ideas Change the lettering to a different name Add more divider grooves for smaller compartments Swap the lid artwork for another species