RigPot — Bankstick Jar with Rig Loops
Created today
Description
RigPot is a 100 mm screw-lid jar with a 30 mm bore, built to ride on a 15 mm bankstick and keep carp rigs organised. A 50 mm side clip grips the stick, and three half-round loops on the remaining sides of the jar hold rigs.
Features
- 30 mm inside diameter, 100 mm tall
- Screw-on lid, printed alongside
- 50 mm clip with open slot for a 15 mm bankstick
- Three half-circle loops, each joined to the jar wall at both ends, spaced at the other three quarters
Print notes
- Loops are flat half-rings, 8 mm tall, no supports needed beyond the jar itself
- Thread clearance is untested; adjust if the lid is tight
Photos
Technical views
More like this
Explore more in Storage & Organization →
Ninja Star Tobacco Can, Inlaid Lid
What it's for A round tobacco can with a snap-fit lid. The lid carries a recessed eight-point ninja star and the curved brand "ORDINARY CAN OF TABACCER", both filled with a contrasting colour. Dimensions Can body: 76 mm diameter, 20 mm tall Lid: 78 mm diameter, 7 mm tall, with 1 mm deep recesses Closed height: 24 mm Remix ideas Swap the brand text or its curve radius Change the star size or recess depth Print the inlays in a second filament colour
220x140x120 mm Square-Bar Storage Frame
Rectangular storage stand made entirely of solid 15 × 15 mm square bars. Two rectangular frames, top and bottom, are joined by four corner posts. A single reinforcing beam runs across the width at the middle of the top frame. All edges are sharp and all faces are flat, with no fillets or curved surfaces. Outer size: 220 mm long × 140 mm wide × 120 mm high Bar section: 15 × 15 mm, solid Posts: four, at the corners, 90 mm visible length between frames Top beam: 15 mm, centred along the length and spanning the width Print: flat bottom face on the bed, no supports needed for the main frame; the top beam spans 110 mm, so expect minor bridging sag Single welded body, symmetrical about both vertical centre planes
peterson 80x95 v3
sdf
Petersson 95x80 v2
A 95 × 80 mm open-top tray, 50 mm tall, with 2 mm walls and a 2 mm floor. What it has 1.5 mm chamfers on the bottom edges and vertical corners; the top rim stays square. Four triangular corner gussets at the rim (z 47–50 mm), each with a 6.1 mm pocket 2.1 mm deep. A 44 mm long, 45 mm tall cut-out in the centre of the -X wall, leaving a 5 mm bottom lip. 13 vertical grooves (2 mm wide, 0.8 mm deep) on the outside of the +X wall. Check before printing The cut-out is 44 mm long so it stays clear of the gussets. Wider cut-outs would cut into them. Does not fit The earlier 155 mm length is gone; the tray is now 80 mm long.
Apothecary Box With Lift-Off Lid
A classic apothecary-style storage box, 6" x 4" x 2", with a separate lid whose inner lip plugs into the body. The two pieces are laid out side by side for viewing and print as two separate jobs, so each fits an 18 x 18 cm bed. Body: 152.4 x 101.6 x 47.5 mm, 2.4 mm walls, chamfered edges Lid: 152.4 x 101.6 mm, 3 mm plate with a 5 mm plug lip Fit: 0.3 mm clearance between lip and body recess Print the lid flat with the lip facing up, no supports needed
Two-Piece Gridfinity Caliper Box
A 6 x 3 unit Gridfinity caliper box split at the middle into two halves, each about 126 x 126 x 25.4 mm, so each fits a 150 mm print bed. Two dovetail keys join the halves. The stepped pocket holds a 9.25 in caliper: a 15.9 mm body slot and a 78 x 97.5 mm head recess, both 12.7 mm deep. The stacking lip and finger scoops are kept. Remix hooks Split position: the cut is at X = 0, on a Gridfinity cell boundary. Moving it in whole 42 mm steps keeps the cells intact. Dovetail size: 8 mm at the root, 13 mm at the tip, 16 mm tall, at Y = ±35. The socket has 0.25 mm clearance. Loosen or tighten it to suit your printer. Joint type: swap the dovetails for round pins or add glue grooves. Pairs with: other Gridfinity bins on a 42 mm baseplate.