ORBISVENTILATION
Created today
Description
Botvent is a plain, tall rectangular holder for a 9V battery, with rows of horizontal vent slots that give it a machine-panel look. No base plate, no add-on parts: just a clean open-top shell.
Features
- Open-top box, 27.2 × 18.2 mm cavity
- 2.4 mm walls and floor
- Six horizontal vent slots on each face
- Square edges, 40 mm tall
Print notes
- Prints upright with no supports needed for the slots at typical settings.
Images
More like this
Explore more in Storage & Organization →
220x140x120 mm Square-Bar Storage Frame
Rectangular storage stand made entirely of solid 15 × 15 mm square bars. Two rectangular frames, top and bottom, are joined by four corner posts. A single reinforcing beam runs across the width at the middle of the top frame. All edges are sharp and all faces are flat, with no fillets or curved surfaces. Outer size: 220 mm long × 140 mm wide × 120 mm high Bar section: 15 × 15 mm, solid Posts: four, at the corners, 90 mm visible length between frames Top beam: 15 mm, centred along the length and spanning the width Print: flat bottom face on the bed, no supports needed for the main frame; the top beam spans 110 mm, so expect minor bridging sag Single welded body, symmetrical about both vertical centre planes
C Clip for 9V Battery Container
What it's for A snap-in C clip that holds a 22 x 33 mm 9 V battery container. The opening sits in the front long wall, so the container presses in and pulls out when the battery needs changing. Dimensions Inside pocket: 22 x 33 mm Height: 20 mm Wall thickness: 2.5 mm Opening: 27 mm wide, leaving 3 mm of retaining wall on each side Outside: 38 x 27 mm Remix ideas Widen the opening to 28 or 29 mm for an easier release. Add a mounting tab or screw holes on the back wall. Print in PETG or nylon for better flex at the snap.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Esquinero en L 20 mm
What it's for Esquinero en L para sujetar la esquina de un taco de hojas de hasta 4 mm de espesor. Las esquinas redondeadas lo hacen más suave al tacto y evitan puntas. Dimensions Brazos: 20 x 20 mm Ranura: 4,6 mm (4 mm de papel + 0,6 mm de holgura) Paredes: 1,6 mm Alto total: 7,8 mm Esquinas exteriores redondeadas con radio de 4 mm Remix ideas Cambiar el largo de los brazos para hojas más grandes. Ajustar la ranura según el espesor del taco. Añadir un agujero para atornillarlo a una superficie.
Spanline — Three-Part Bookshelf Riser
Spanline is a bridge-shaped bookshelf riser, 450 × 125 × 125 mm when assembled, split into three sections that each fit a 200 mm print bed. Sliding dovetail joints lock the sections together, and the tunnel underneath stays open for storage. Print layout Three separate pieces, spaced 20 mm apart, none touching. Each piece is flipped so the flat top face sits on the bed, so no supports are needed for the arch. Each piece is about 162 mm long, including its dovetail tongue. Features 16 mm top and walls with a 25 mm rounded inner arch Dovetail tongue-and-groove joints with 0.25 mm clearance Shallow rib under the top of each section Assembly Slide Part B onto Part A's tongue from the side, then slide Part C onto Part B's tongue.