Made by PaprikaQuail
Created 1 months ago
Description
A solid, flat-backed Christmas bell ornament designed for straightforward FDM printing. The model combines a traditional flared silhouette with a top bow and an integrated hanging ring.
Prints completely flat on the bed with no supports required. Ideal for PLA or PETG.
Images
Evergreen Ring reduces the Christmas ornament to a clean silhouette: an open circular ring with a hanging loop, a pair of small three-tier trees tucked into the lower-right corner, and a large six-armed snowflake filling the top-left, its outer arms running into the ring and clipped by it. The right-hand tree sits fully inside the hoop, its tiers clear of the ring, with only its trunk running down into the bottom of the ring. The companion tree to the left is about 1.5 mm larger, with roughly 1 mm separating the pair, so the motif reads as a deliberate little grove rather than a repeat. The snowflake is centred about 12 mm in from the corner, and the arms that meet the ring are what hold it in place. Ring, trees and snowflake all stand the same 3 mm tall, giving the piece a single even plane that sits flat against a branch, a window or a gift tag. Every element is joined to the hoop, so the whole ornament prints as one solid piece with no assembly and no loose parts. Dimensions Ring: 60 mm across, 66 mm tall overall including the hanging loop, 3 mm thick Trees: two small trees occupying roughly 23.4 × 15.6 mm combined, 3 mm thick Snowflake: about 32.8 × 34 mm, 3 mm thick Features Open-ring ornament with an integrated hanging loop Two small three-tier trees side by side in the lower-right corner, with the tiers fully clear of the ring One tree about 1.5 mm larger than the other Large branched snowflake in the top-left corner, its outer arms cut off by the ring and fused to it Only the tree trunks and the snowflake's outer arms meet the ring, keeping the scene connected Uniform 3 mm thickness across every part Prints as a single piece, no supports needed Print notes Lay the ornament flat on the plate; the even thickness means no tall overhangs Any filament works — use contrasting colours for the trees and snowflake if you print in multiple colours

A flat, round hanging ornament shaped as a smooth spiral curl. The spiral is one continuous band that swells through the middle and thins to fine points at both ends, like a calligraphy stroke, with even spacing between turns. It lies flat, so the ornament sits close against a tree branch or a wall instead of projecting outward. A round hanging loop sits at the top at the 12 o'clock position, and the whole ornament prints as one piece in a single color. Specs Overall size: about 45 × 56 mm, 5 mm thick Spiral: one continuous band, tapered to fine points at both ends, heaviest at the middle Turns: about 3.5, evenly spaced Hanging loop at the top, sized for thread, ribbon or a wire hook Single color, one-piece print Flat face: hangs flush against the tree or a wall Prints without supports on its flat face Loop joint: the tapered outer end meets the ring over a small area, so this is the weak point — hang it gently or reinforce that joint if it sees rough use
A small snowflake pin with six branched arms, made to be worn on a shirt. Two loops on the back take a standard safety pin, so the snowflake sits on the fabric like a brooch. Six-arm snowflake with side branches and rounded tips Two back loops, 8 mm apart, for threading a safety pin Flat front face prints directly on the plate No supports needed Roughly 31 mm across and under 6 mm thick
A hollow Christmas bauble with a six-armed snowflake cut through the front and back. The snowflake branches are set at a 40° angle so no island of shell is trapped between them; the cutout stays one connected shape. Rings of small round through-holes sit above and below the middle, and the equator is left plain. Raised bands run above and below the equator, and a cap with a hanging loop sits at the top. The bottom is flattened into a small footing so the ornament can stand upright on the print plate; the curved lower sides generally need supports. Specs Overall size on the print plate: 59.9 mm wide × 59.7 mm deep × 71.5 mm high Ball diameter: 60 mm Wall thickness: 2.5 mm, hollow shell Bottom footing: about 19 mm across Cutouts: one six-armed snowflake through the front and one through the back, about 22 mm across with fine branches around 1.8 mm thick Snowflake branches: 40° branch angle, arranged so no detached wall islands are left inside the cutouts Dot holes: 12 above the middle and 12 below, each a 3.2 mm hole straight through the wall; no hole row at the equator Bands: raised rings above and below the equator Top: cap with hanging loop Printing: single piece; supports needed on the curved sides Use: Christmas tree ornament or hanging decoration; the flattened base also lets it stand on a flat surface
What it's for A snowflake brooch for shirts and fabric. Two loops on the back take a standard safety pin. The flat front prints face-down on the plate, so no supports are needed. Dimensions About 31 mm across, under 6 mm thick Loops on the back sit 8 mm apart Six tapered arms with two branch pairs each Colors White: arms and center hexagon Light cyan: diamond tips Stardust gray: branch beads, center ring and back loops Remix ideas Swap the gray and cyan roles Scale up for a magnet or ornament Replace the loops with a flat magnet pocket
A cigarette you can't smoke but can play: an 84 mm-long fipple whistle disguised as a filter-tipped stick, complete with an orange ember tip, a white paper body and a tan filter. Inhale through the filter end and air slips through the intake hole near the ember, runs a thin flat duct across a window and breaks over a sharpened edge — the classic whistle mechanism, wearing a noir prop's silhouette. It is an inhale-only instrument; blowing back out through it will sound weak or not at all. This version is tuned for a softer, lower note: the duct is narrow and shallow, the window is long with a gentle ramp, and the intake is widened a touch to keep the hiss down. A gentle, steady inhale gives the smoothest sound; a hard pull turns breathy. Design notes Three colour-coded sections in the viewer: Ember Tip, Paper Body and Filter, printed as a single piece. The underside is flattened, so it sits stable on the plate and needs no supports. Keep your lips clear of the intake hole while you inhale — that hole is the voice. Tone stays tunable: a longer window takes it darker, a slightly more open duct brings back volume if it comes out too faint. Pairs well with a trench coat, a rainy window, and anyone who appreciates a joke that also functions.