Created 1 months ago
Description
Base structure for the Moroccan Unity Day modular parade truck. Built to carry standard 6mm axle rods and accept top-deck cabin and cargo payloads.
This is a specific-fit frame, not a universal runner. Check the axle bore and mounting distances before committing filament:
Prints top-down or bottom-up depending on your preference for bridging, but the internal grid is fully pocketed to drop weight while keeping the deck rigid. Minimum wall thickness is locked at 2.5mm for an easy two-wall pass on a 0.4mm nozzle.
Images
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
A two-piece hinged clamp for a 38.5 mm motorcycle fork tube, with an L-shaped bracket that carries a 10 mm hole and a 4 mm wire slit for a turn signal post. The halves swing open on an M3 hinge pin and close with one M6 bolt and a hex nut pocket, so the fork stays on the bike. The hinge sits outside the ring on small webs, so the knuckles clear the opposite half when it swings. Bore: 38.0 mm Height: 24 mm, wall 3.5 mm Hinge pin: M3 × 30 bolt or 3 mm rod Clamp bolt: M6 with nut Print the front half with its L bracket, and the rear half separately
What it's for A one-piece floor cradle that holds a triple 12V socket adapter horizontally under a dashboard. The front and top stay open, so the sockets and power switches remain reachable, and side windows keep the side USB ports clear. Dimensions Adapter: 100.4 x 60.85 x 31.72 mm, about 1 mm clearance Side walls: 3 mm thick, 14 mm tall Side windows: 18 mm long, centred 51.38 mm from the front (plus 1 mm clearance) Back lip: 12 mm tall with reinforced corners Mounting ears: 16 mm each end, countersunk screw holes Remix ideas Change the window length to fit a different USB port. Add a third screw hole at the back. Lengthen the ears for wider mounting.
A 2x4 plate with no way to pass a Technic pin or axle through it is a dead end in a studless build. This plate has three holes on the centre line, so pins and axles go straight through. Six are laid out flat for one print run. Key numbers Plate: 32 x 16 mm, 3.2 mm thick, studs on 8 mm pitch Studs: 4.8 mm diameter, 1.8 mm tall Holes: three, 4.8 mm diameter, on the centre line, 8 mm apart Print: flat, no supports, 0.2 mm layers; test one first to check clutch fit
A knurl-free drive wheel for a pinch-feed wire feeder, built like a small industrial pulley: a 24 mm roller with a hub on one side and a blind D-bore that slips over a 5 mm D-shaft. The model is just the roller, standing on its hub and ready to slice. Design notes Blind D-bore, open on the hub face and closed by a wall on the far end, so the closed end shows which side stays out. M3 grub screw hole with a trapped hex nut that slides in through a slot open to the rim. Counterbored screw recess 2 mm deep, so a headed M3 screw sits below the surface and a nylon or TPU sleeve goes on smooth. Hub spaces the roller off the motor face so the two do not rub. Printing Stands on the hub with the bore opening onto the bed, so there is no bridging inside the bore and no supports are needed. Printing upright keeps the roller round. Suggested: PETG, ASA or nylon, 3 or more walls, 25–30% infill.
Schneekufen für Skateboards, die auf Schnee und Eis gefahren werden. Die Kufe wird über das Truck-Lochbild an der Achsaufnahme verschraubt und sorgt für Führung auf glatten Untergründen. Die Sohle ist 170 mm lang, 50 mm breit und 2 mm dick; der mittlere Steg ist 6 mm dick. Die Sohle ist über die gesamte Länge flach ausgeführt. Montageplatte, Steg und Lochbild sitzen 25 mm zum hinteren, breiten Ende hin versetzt, sodass der Steg voll auf dem flachen Teil der Sohle steht. Das vordere Ende verjüngt sich geradlinig zu einer etwa 10 mm breiten, leicht gerundeten Spitze; das gegenüberliegende Ende bleibt breit. Beide Sohlenenden haben eine 3-mm-Fase. Für ein Skateboard sind zwei Kufen nötig. Maße und Montage Gesamtmaß: 170 mm lang, 50 mm breit, 33 mm hoch Sohle: 2 mm dick, durchgehend flach Mittlerer Steg: 6 mm dick, steht voll auf der flachen Sohle Verjüngung: geradlinig zur Spitze, Spitzenbreite etwa 10 mm, leicht gerundet Gegenüberliegendes Ende: breit ausgeführt Enden: 3-mm-Fase an beiden Sohlenrändern Befestigungspunkt: Montageplatte mit Truck-Lochbild 53 × 41 mm, 25 mm zum breiten Ende versetzt Schraublöcher: 5,4 mm, oben angesenkt Befestigung: handelsübliche Schrauben und Muttern Die Maße sind Standardwerte und nicht an ein bestimmtes Board angepasst – vor dem Druck mit dem eigenen Truck-Lochbild abgleichen Druck Passt auf das Druckbett eines A1 mini Durchgehend flache Sohle: kein Stützmaterial an der Spitze nötig 2-mm-Sohle: auf dem A1 mini etwa die Untergrenze; die Sohle wird flexibel und gibt unter Last nach, daher mit mehreren Wandlinien drucken Material: PETG oder ASA Stückzahl: zwei Kufen pro Skateboard