Description
Model truck wheels usually snap at the hub or require a nest of supports just to print the rims. This one prints entirely flat on the bed, bridging cleanly across the inner rim recess, with treads chunky enough to actually grip rough surfaces instead of spinning out.
Specifications
- Diameter: 80 mm
- Width: 30 mm
- Axle: 8 mm hex shaft
- Print orientation: Flat on its side (no supports needed)
Images
More like this
Explore more in Automotive, RC & Hobby →
20
RC wheels always crack at the hub after a bad jump, or spin out when the stock treads wear flat. This is the right-side replacement—built dense enough to survive a hit, with directional treads angled specifically for the starboard side to keep it digging into the dirt instead of skating over it. Fitment Details Dimensions: 65 mm outer diameter, 18 mm width. Axle: 5.2 mm central bore (fits standard 5 mm RC axles with clearance). Print Settings: Lay it flat. No supports needed. Run it solid or with dense gyroid infill to keep the hub from tearing out under torque.
10-Camion
A rugged, 85mm rear-right truck wheel ready for hard use. The tire features deep, directional tread angled specifically for the right side of the vehicle, ensuring proper grip and a realistic mirrored stance compared to its left-side counterpart. Design Notes Dimensions: 85mm outer diameter, 35mm width. Mounting: Standard 6mm pass-through axle hole. Detailing: Deep recessed rim with a prominent center hub and six realistic lug nuts. Printability: Designed to print flat on its inner face with no supports required.
9-Camion
Heavy-duty rear wheel designed for modular truck assemblies. Features an 84mm outer diameter with aggressive block treads and a deep-dish rim structure. Built to transfer high torque from a printed axle without slipping. Prints flat on the inner face. Diameter: 84mm (including treads) Width: 30mm (32mm at hub) Axle bore: 9mm hex socket (across corners) Mounting: Prints flat on the Z-axis, no supports required. Material: Designed for rigid filaments like PLA or PETG.
8-Camion
A truck missing one wheel is just a seesaw that scratches the floorboards. Stripped hex hubs or worn treads usually end a run early; this is the right-side replacement to get it rolling flat again. The tread channels are cut at a 20-degree angle to specifically mirror the left side, keeping the traction profile symmetrical. Fitment and Print Details Outer Diameter: 78 mm Width: 26 mm Drive Interface: Standard 12 mm RC hex socket (6 mm deep) Axle Clearance: 5.2 mm bore, clearing standard 5 mm axles. Printing: Drop it flat on the inner face (the hex side). No supports needed; the outer rim inset chamfers cleanly. Needs dense infill around the hub to prevent the hex from rounding out under torque.
7-Camion
This is a rugged, heavy-duty truck wheel designed to anchor the front-left corner of a modular exhibition chassis. Coming in at 78mm in diameter, it features a deep-dish rim, aggressive sidewall tread cuts, and a prominent central hub studded with hex lug nuts. Fabrication Notes Print Orientation: Flat on its back face. Overhangs: Sloped internal cavities mean it requires absolutely zero supports. Interface: Features an 8.2mm central clearance bore to slide onto standard chassis axles. Strength: Designed thick with minimal internal bridging for high impact resistance.
Tabletop Cornhole Deck
A desktop-scale modular cornhole kit scaled to a 175mm deck length, complete with a print-in-place flexure bag that collapses to clear the main bore. The deck prints upside down (or flat) to avoid supports inside the main cavity, while the folding leg frame snaps securely into the 4.2mm frame hinges. Fitment notes Bore Size: 24mm diameter target hole. Bag Size: 21x21mm overall, connected by 0.4mm thick living-hinge webs. Leg Hinge: 4.2mm deck bore, 3.5mm pins on the leg frame — expects a firm flex to seat.