21mm Disk Holder with Snap Lip
Created today
Description
What it's for
A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place.
Dimensions
- Outer diameter: 27 mm, 4.7 mm tall
- Disk pocket: 21.4 mm diameter, 2.5 mm deep
- Retaining lip: 0.5 mm overhang with a tapered lead-in
- Rear window: 17 mm, for pushing the disk out
- Eyelets: 4 mm holes, 9 mm pads, on both sides
Remix ideas
- Increase the lip overhang for a firmer grip
- Remove the rear window for a closed back
- Add text or a chamfer ring around the edge
Images
More like this
Explore more in Keychains & EDC →
Round Turbah Keychain Container
A 40 mm round container with a press-fit lid and a keyring loop, sized for a 35 mm turbah disc. The lid carries a red medallion with a silver ornamental pattern of petals, dots and rings. It has no text. Remix hooks Interior fit: the cavity is 36 mm wide; change ID for a tighter or looser disc. Height: the base is 11 mm and the lid adds 3 mm for a stack of about 14–15 mm; raise the base height for thicker discs. Ornament: petal count (12 at 30° steps), ring diameters and relief height (0.4 mm) are easy to change. Lid grip: the 30 ribs around the rim can be removed or swapped for a knurl. Colours: print black, red and silver as separate colour regions in a multicolour slicer. Pairs with: a split ring or lanyard clip through the 6 mm loop hole.
Hollow Sphere Keychain, 33 mm Screen Opening
Two-piece hollow sphere keychain with a 33 mm round screen opening in the front and a 3.3 mm ring hole through the top wall. The halves snap together with small bead pegs and can be pulled apart by hand. Body: about 56 mm sphere with two ear bumps, 2 mm wall, flat front face Screen opening: 33 mm diameter, through the front wall into the hollow interior Ring hole: 3.3 mm, a plain hole through the top wall on each side, with no inner sleeve Joint: three bead pegs and undercut sockets, pull apart along the left-right axis Print: each half sits cut-face down, no supports needed for the outer curve
Star Apple Watch Keychain Enclosure
A rounded five-point star shell that holds an Apple Watch SE 44 mm (A2352) as a keychain, with the real display open at the front. Two printed parts: a front shell (print mating face down) and a rear cover (flat face down) joined by four M2 screws. Remix hooks Watch fit: case 44 x 38 mm, 0.4 mm clearance per side, cavity depth 11.2 mm, corner radius 8 mm. Change clr, D and cav_r to tune the fit. Display window: 38.4 x 32.8 mm. This is an estimate, so confirm it against the watch. Crown, button, mic and speaker cutouts: positions are placeholders on the right and left sides. Measure the watch and move them before printing. Star size: the star_pts radii (50 / 33 mm) set the roughly 80 mm span. Shrinking the valley radius thins the wall near the cavity corners. Keyring hole: 5 mm at the top point. Raise ringd or move ringpos for a bigger ring. Charging opening: 32 mm round hole in the rear cover (charge_d). Pairs with: M2 x 8 mm screws, a small split ring, or a TPU bumper variant. Still to verify Crown and button height and position Speaker and mic positions Exact display window size Rear sensor bulge depth Treat the first print as a fit prototype. It is not load-rated.
FlexiLink — Llavero Articulado TAMARA
Este es un llavero articulado de impresión print-in-place que no requiere soportes ni montaje. Las letras conforman el cuerpo de los propios eslabones, y se unen mediante un sistema de pasador cautivo oculto con holguras diseñadas para liberar el movimiento tan pronto como la pieza termina de imprimirse. Características Legibilidad mejorada: Los pasadores se conectan directamente a los laterales de las letras, manteniendo el interior limpio. Articulaciones sueltas: Diseñadas con 0.4 mm de tolerancia, pensadas para la calibración habitual de PLA en impresoras modernas. Sin ensamblaje: Todo el llavero se imprime como un solo cuerpo que se pliega. Anilla integrada: El extremo cuenta con una gaza con espacio para una anilla estándar de llaves.
Portachiavi 30x45x4 mm con battistrada
Portachiavi rettangolare 30x45 mm, spessore 4 mm, con cavità interna chiusa e disegno di battistrada inciso sulla faccia superiore. Misure da controllare Cavità interna: disco Ø26 x 1 mm, a metà spessore (da 1,5 a 2,5 mm), con pareti da 2 mm ai lati e 1,5 mm sopra e sotto. Non è visibile dall'esterno. Foro passante: Ø3 mm, a 3,5 mm dal bordo corto. Battistrada: tacchetti a V e scanalature laterali, profondità 0,6 mm. Compatibilità Il vano è pensato per un inserto piatto fino a Ø25 x 0,8 mm (moneta sottile, rondella, disco magnetico), da inserire con una pausa di stampa al layer 1,5 mm. Non adatto a inserti più spessi di 1 mm. Stampa senza supporti, con la faccia battistrada verso l'alto.
6 mm Ball-Joint Crystal Dragon, 42 Segments
A print-in-place articulated dragon built on 6 mm balls in 7 mm sockets, with faceted hexagonal crystal clusters on the head, spine, legs and tail tip. Fit and clearance Joint: 6 mm ball in a 7 mm socket (0.5 mm radial clearance), 5 mm neck opening so the ball cannot pull out. Chain: 42 body segments at 12 mm pitch, plus four legs of two segments each. Check before printing: the laid-out dragon is roughly 350 mm long in its S-curve, so verify your bed size or scale it down in the slicer. Scaling below about 80% closes the 0.5 mm clearance. Not suited to Printers with a bed under about 250 mm without rescaling. Printing the crystals first: the model lies flat on the bed, crystals pointing up, flat horns on the bed. Fast, uncooled printing: joint gaps need slow, well-cooled layers.