Hollow Sphere Keychain, 33 mm Screen Opening
Created today
Description
Two-piece hollow sphere keychain with a 33 mm round screen opening in the front and a 3.3 mm ring hole through the top wall. The halves snap together with small bead pegs and can be pulled apart by hand.
- Body: about 56 mm sphere with two ear bumps, 2 mm wall, flat front face
- Screen opening: 33 mm diameter, through the front wall into the hollow interior
- Ring hole: 3.3 mm, a plain hole through the top wall on each side, with no inner sleeve
- Joint: three bead pegs and undercut sockets, pull apart along the left-right axis
- Print: each half sits cut-face down, no supports needed for the outer curve
Images
More like this
Explore more in Keychains & EDC →
Star Apple Watch Keychain Enclosure
A rounded five-point star shell that holds an Apple Watch SE 44 mm (A2352) as a keychain, with the real display open at the front. Two printed parts: a front shell (print mating face down) and a rear cover (flat face down) joined by four M2 screws. Remix hooks Watch fit: case 44 x 38 mm, 0.4 mm clearance per side, cavity depth 11.2 mm, corner radius 8 mm. Change clr, D and cav_r to tune the fit. Display window: 38.4 x 32.8 mm. This is an estimate, so confirm it against the watch. Crown, button, mic and speaker cutouts: positions are placeholders on the right and left sides. Measure the watch and move them before printing. Star size: the star_pts radii (50 / 33 mm) set the roughly 80 mm span. Shrinking the valley radius thins the wall near the cavity corners. Keyring hole: 5 mm at the top point. Raise ringd or move ringpos for a bigger ring. Charging opening: 32 mm round hole in the rear cover (charge_d). Pairs with: M2 x 8 mm screws, a small split ring, or a TPU bumper variant. Still to verify Crown and button height and position Speaker and mic positions Exact display window size Rear sensor bulge depth Treat the first print as a fit prototype. It is not load-rated.
6 mm Ball-Joint Crystal Dragon, 42 Segments
A print-in-place articulated dragon built on 6 mm balls in 7 mm sockets, with faceted hexagonal crystal clusters on the head, spine, legs and tail tip. Fit and clearance Joint: 6 mm ball in a 7 mm socket (0.5 mm radial clearance), 5 mm neck opening so the ball cannot pull out. Chain: 42 body segments at 12 mm pitch, plus four legs of two segments each. Check before printing: the laid-out dragon is roughly 350 mm long in its S-curve, so verify your bed size or scale it down in the slicer. Scaling below about 80% closes the 0.5 mm clearance. Not suited to Printers with a bed under about 250 mm without rescaling. Printing the crystals first: the model lies flat on the bed, crystals pointing up, flat horns on the bed. Fast, uncooled printing: joint gaps need slow, well-cooled layers.
Schlüsselanhänger paula
Schlüsselanhänger mit Namen Paula, bei dem die Schrift nicht flach untergeht: Sie steht 0,5 mm erhaben auf der Platte und lässt sich mit dem Finger ertasten. Das Kettenloch sitzt seitlich, damit der Ring nicht über die Buchstaben schleift. Platte: 30 × 14 × 2 mm, Ecken mit 3 mm abgerundet Schrift: „Paula“ in Lobster, 0,5 mm erhaben Kettenloch: 3,5 mm Durchmesser, linke Seite Druck: flach auf der Platte, ohne Stützen, 0,2 mm Schichthöhe empfohlen
Pion Trivial Pursuit 26 mm, 6 camemberts
Support de pion rond de 26 mm de diamètre avec 6 logements en secteur, accompagné de 6 camemberts (secteurs de 60°) à insérer dans les logements. Les pièces s'impriment séparément, à plat. Support : diamètre 26 mm, hauteur 6 mm, fond 2 mm, logements de 4 mm de profondeur Cloisons entre logements : 1,2 mm Camemberts : 6 pièces, hauteur 3,5 mm, avec un plot de préhension de 1,5 mm Jeu d'insertion : 0,25 mm par côté Matériau conseillé : PLA ou PETG, une couleur par camembert
Stitch Head Bead With Ears
A round Stitch-style head bead with two pointed ears, a lighter face patch, eyes and a nose, threaded by a vertical hole for cord or wire. Remix hooks Head size: the head radius is 13 mm (26 mm across). Scale it down for jewelry-sized beads; keep the hole at 3.5 mm or larger for cord. Hole diameter: 3.5 mm runs top to bottom between the ears. Widen it for paracord or narrow it for thin elastic. Ear angle and length: ears are about 21 mm long, splayed 55° outward. Lower the angle for droopy ears, or shorten them for a chunkier keychain bead. Colours: the head, face patch, inner ears and eyes are separate regions, so they suit multicolour printing with filament swaps. Pairs with: plain round spacer beads, a keyring clasp, or a row of beads for a bag charm.
Indian Number Plate Keychain HR82 6791
A rectangular Indian-style number plate keychain with the registration HR82 6791 in raised black letters on a white plate. 70 × 20 mm plate, 3 mm thick, with rounded corners Text raised 0.75 mm for clean printing with a 0.4 mm nozzle 4 mm ring hole on the left side Flat back, no supports needed Single connected piece, white base with black text