Made by OnyxZebra
Created 1 months ago
Description
Solid registration plate built to clear standard 25mm split rings.
The 4.5mm bore is strictly for split rings or small carabiners; it will not accept wide webbing or thick lanyards.
Photos
Technical views
Bharat Key is a miniature Indian-style number plate keychain made to carry the exact registration PB 12 V 6821. The long, slim plate pairs a light grey/white base with a thin raised black border and bold black lettering raised on a single horizontal line. The keyring hole sits at the extreme left, ringed with raised black for strength, while the registration stays centred in the space that remains. No blue IND strip, flag, extra colour or decoration is present, so the tag keeps a clean number-plate look while staying sturdy enough for a keyring. Dimensions Plate: 75 × 20 × 2.5 mm Raised border and text: 0.6 mm above the base; border 1 mm wide Keyring hole: 4 mm diameter, cut fully through at the extreme left Hole ring: raised black ring around the hole for extra strength Features Exact registration text: PB 12 V 6821 on one horizontal line Bold black lettering raised above a light grey/white base Thin raised black border around the whole plate One circular keyring hole at the extreme left, fully through the plate Raised black ring around the hole to reinforce the keyring area Flat rectangular body with slightly rounded corners and a smooth flat backside Light grey/white base and black details only — no blue, no flag, no logos or decorations Print notes Print flat on the back; no supports are needed. The raised border and lettering sit 0.6 mm above the base and read clearly at miniature scale. Keep the 4 mm hole clear so the plate hangs cleanly on a keyring.
A two-piece luggage tag that holds a standard business card and hides the address behind a sliding cover panel. The body is 96 × 66 mm with an 86 × 56 mm card window (a 5 mm border on every side) and a side tab with a 6 mm strap hole. The cover prints flat beside the body and slides in from the right end through grooves in the border. Remix hooks Card window (86 × 56 mm): sized for an 85 × 55 mm card with 0.5 mm play per side. Change both numbers together for other card sizes, and adjust the body size to keep the border. Border width (5 mm): the body is window size plus 10 mm per axis. A wider border gives more room for the grooves and a sturdier tag. Groove clearance: the groove has 0.8 mm of side play and 0.2 mm of height play around the cover. Tighten or loosen these to suit your printer, since this is the fit most likely to need tuning. Detent bump: the cover can slide open on its own, and the card drops in from the top, so it is the only thing keeping the card in. A small bump on the cover and a matching dimple in the groove would hold it shut. Strap tab: 22 × 30 mm and 2.6 mm thick, with a 6 mm hole. Enlarge the hole for wider straps or cable loops. Body thickness: 4.6 mm overall. Thinning it saves filament but shortens the groove and window walls. Pairs well with Split-ring or lanyard clip through the strap hole A different colour for the cover, so the sliding piece reads at a glance Embossed or engraved text on the cover top, such as a name or a "contact owner" line Print notes Print both pieces flat, as laid out on the plate. Check the cover fit after the first print before committing to a batch.
A compact, D-shaped snaplink in the spirit of the little accessory carabiners that hang off backpack straps and key rings. The 70 mm body carries a pivoting gate and a thin flexure spring that nudges it shut, all printed together in one go. Pop the gate open with a thumb, slip a key ring or bottle loop in, and let it snap back. Not rated for climbing or load-bearing safety use. Keep it to keys, bottles and bag clips. Design notes Size: 70 mm long, 38 mm tall, 8 mm thick. Gate: hinged at the right end, swings inward about 32° for a roughly 12 mm opening. Spring: a 1 mm living-hinge arm along the bottom wall returns the gate to closed. Print-in-place: 0.5 mm clearance gaps around the gate and spring, so no assembly is needed. Material: PETG is recommended for the flexing spring arm. Work the gate a few times after printing to free it. Tuning: if the gate sticks or rattles, adjust the clearance for your printer. The spring thickness sets how stiff the gate feels.
A flat 65 × 17 mm number plate keychain built around the three things that ruin a printed tag: a hole that tears out, lettering that runs off the right edge of the plate, and a border crowded with extra frames. The hole sits inside a raised black ring instead of hanging on a thin web of plastic, so a heavy bunch of keys has something solid to pull against. The registration line sits on one horizontal line, raised 0.6 mm so it stays readable instead of rubbing smooth in a week, and it starts clear of the ring so nothing touches the hole. Print and fit Plate: 65 × 17 × 2.5 mm, corners rounded, smooth flat back. Keyring hole: one 4 mm through-hole at the far left, 7 mm in from the end so its ring clears the border, fully open through the base, with its own clear area so it never meets the text. Hole ring: a 9 mm black raised ring around the hole, kept neat and with no other decoration around it. Lettering: "PB 27 F 9146" on one line, raised 0.6 mm in a heavy bold face with even spacing, sized to fit the space between the ring and the right border. Border: a single thin black raised border around the whole plate, 0.6 mm high — no inner frame. Base: light grey, flat and unbroken underneath, prints without supports; the detail all sits on the raised top face, so a two-colour print or a paint fill both work. The text sits a little right of the plate's true centre because the hole takes up the left end — a truly centred line would run into the ring. If you change the registration, shorten the text rather than the plate, or the line will overrun the border on the right side.
A miniature Indian-style number plate keychain reading PB 27 F 9146 on a single line, with a thin raised border and a 4 mm keyring hole at the left end. Size: 75 × 20 mm, 2.5 mm base Raised text and border: 0.6 mm Light grey base with black text and border Rounded corners, flat smooth back One 4 mm hole at the left end No flag, IND strip or blue section For a two-colour print, pause for a filament change at the 2.5 mm layer. The text is centred in the area to the right of the hole.
A keychain for the keyring that always ends up at the bottom of the bag: a diamond-shaped yellow warning sign with "SAFETY THIRD" in black on two lines, and a loop at the top apex for the ring. It is oversized on purpose, so it reads as a sign rather than a tag and is easy to find by feel and grab. Fit and print Overall size: about 97 mm across and about 107 mm tall including the top loop — big for a keychain, deliberately. Lettering: both lines are centred in the diamond at a size that keeps "SAFETY" inside the inner border, with a small gap at the top corners. Attachment: 6 mm hole through the plain yellow loop at the top apex; no black ring around the hole. Two-colour print: yellow base with the black border and text raised 0.8 mm; swap filament at 0.8 mm. Assembly: prints as one piece, with the black layer sitting proud of the yellow face.