Safety Third Diamond Keychain
Created today
Description
A keychain for the keyring that always ends up at the bottom of the bag: a diamond-shaped yellow warning sign with "SAFETY THIRD" in black on two lines, and a loop at the top apex for the ring. It is oversized on purpose, so it reads as a sign rather than a tag and is easy to find by feel and grab.
Fit and print
- Overall size: about 97 mm across and about 107 mm tall including the top loop — big for a keychain, deliberately.
- Lettering: both lines are centred in the diamond at a size that keeps "SAFETY" inside the inner border, with a small gap at the top corners.
- Attachment: 6 mm hole through the plain yellow loop at the top apex; no black ring around the hole.
- Two-colour print: yellow base with the black border and text raised 0.8 mm; swap filament at 0.8 mm.
- Assembly: prints as one piece, with the black layer sitting proud of the yellow face.
Images
More like this
Explore more in Keychains & EDC →
Indian Number Plate Keychain HR82 6791
A rectangular Indian-style number plate keychain with the registration HR82 6791 in raised black letters on a white plate. 70 × 20 mm plate, 3 mm thick, with rounded corners Text raised 0.75 mm for clean printing with a 0.4 mm nozzle 4 mm ring hole on the left side Flat back, no supports needed Single connected piece, white base with black text
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
35 mm Threaded Keychain Container, Rosette Lid
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
21mm Disk Holder with Snap Lip
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge
Round Turbah Keychain Container
A 40 mm round container with a press-fit lid and a keyring loop, sized for a 35 mm turbah disc. The lid carries a red medallion with a silver ornamental pattern of petals, dots and rings. It has no text. Remix hooks Interior fit: the cavity is 36 mm wide; change ID for a tighter or looser disc. Height: the base is 11 mm and the lid adds 3 mm for a stack of about 14–15 mm; raise the base height for thicker discs. Ornament: petal count (12 at 30° steps), ring diameters and relief height (0.4 mm) are easy to change. Lid grip: the 30 ribs around the rim can be removed or swapped for a knurl. Colours: print black, red and silver as separate colour regions in a multicolour slicer. Pairs with: a split ring or lanyard clip through the 6 mm loop hole.
Portachiavi 30x45x4 mm con battistrada
Portachiavi rettangolare 30x45 mm, spessore 4 mm, con cavità interna chiusa e disegno di battistrada inciso sulla faccia superiore. Misure da controllare Cavità interna: disco Ø26 x 1 mm, a metà spessore (da 1,5 a 2,5 mm), con pareti da 2 mm ai lati e 1,5 mm sopra e sotto. Non è visibile dall'esterno. Foro passante: Ø3 mm, a 3,5 mm dal bordo corto. Battistrada: tacchetti a V e scanalature laterali, profondità 0,6 mm. Compatibilità Il vano è pensato per un inserto piatto fino a Ø25 x 0,8 mm (moneta sottile, rondella, disco magnetico), da inserire con una pausa di stampa al layer 1,5 mm. Non adatto a inserti più spessi di 1 mm. Stampa senza supporti, con la faccia battistrada verso l'alto.