Frostmourne Fantasy Sword Sculpture
Created today
Description
A detailed gothic fantasy sword sculpture, laid flat on the print plate with the handle on the left and the blade pointing right. The pommel underside and the guard spikes are trimmed flush so the whole sword rests on the plate at z=0, which makes it sit stable while printing and lets it lie flat as a display piece.
The blade runs about 157 mm long with a beveled, notched double edge, rune cuts down the middle and a thin central groove. The crossguard is the widest point at roughly 101 × 76 mm, built as a central block with curved horns, an upper horn, a rear spike and a forward spike. The grip is a core wrapped in raised rings, and the pommel carries a collar, radial spikes and a tail spike. Everything is modelled as one connected solid with the deep relief, sharp edges and layered ornament of the original design.
- Blade, crossguard and wrapped grip as one connected piece
- Beveled double edge with sculpted runes and a centre groove
- Curved horn crossguard with rear and forward spikes
- Round pommel with collar, radial spikes and tail spike
- Pommel and guard spike tips trimmed flat to sit on the plate
- Prints in millimeters; the thinnest spike tips taper down to about 1.5 mm
The thin spike tips are the fragile part of the model — handle them carefully when removing the print, and thicken them if you want a sturdier piece.
Images
More like this
Explore more in Desk & Tech →
Frostmourne Fantasy Sword Sculpture
A detailed gothic fantasy sword sculpture, laid flat on the print plate with the handle on the left and the blade pointing right. The pommel underside and the guard spikes are trimmed flush so the whole sword rests on the plate at z=0, which makes it sit stable while printing and lets it lie flat as a display piece. The blade runs about 157 mm long with a beveled, notched double edge, rune cuts down the middle and a thin central groove. The crossguard is the widest point at roughly 101 × 76 mm, built as a central block with curved horns, an upper horn, a rear spike and a forward spike. The grip is a core wrapped in raised rings, and the pommel carries a collar, radial spikes and a tail spike. Everything is modelled as one connected solid with the deep relief, sharp edges and layered ornament of the original design. Blade, crossguard and wrapped grip as one connected piece Beveled double edge with sculpted runes and a centre groove Curved horn crossguard with rear and forward spikes Round pommel with collar, radial spikes and tail spike Pommel and guard spike tips trimmed flat to sit on the plate Prints in millimeters; the thinnest spike tips taper down to about 1.5 mm The thin spike tips are the fragile part of the model — handle them carefully when removing the print, and thicken them if you want a sturdier piece.
Gothic Frostmourne 2U Backspace Keycap
A 2U backspace keycap with a rounded rectangular body, hollow underside and cross stem. The top carries a raised gothic relief: a Frostmourne-style sword runs horizontally with the grip at left and the blade at right, four sculpted skulls sit in the corners, and rows of gothic spikes frame the top and bottom edges around a central diamond ornament. The cap measures 37 × 18 mm with an 8 mm body; the sword relief reaches 3.9 mm, the gothic spikes 4.1 mm and the skulls 2.3 mm. Note: no stabilizer slots are included, so check whether the 2U backspace position on your board needs them before printing. Remix hooks Sword depth: The sword is the tallest relief at 3.9 mm. Raise or flatten it to trade drama for a lower-profile cap. Skull scale: The corner skulls are 2.3 mm tall; enlarge them or simplify the teeth if your printer struggles at this scale. Frame density: The gothic spikes are 4.1 mm tall and define the outer silhouette. Thin them, space them wider, or swap the central diamond for another ornament. Body fit: 37 × 18 mm and an 8 mm body are the starting values. Adjust skirt height, dish depth or stem clearance to suit your board, and add stabilizer slots if needed. Variants: Try a smoother stone background, a single central skull, or a mirrored sword for a different corner balance. The cap pairs naturally with other dark-fantasy keycaps as a statement backspace.
Bộ Keycap Bàn Chân Và Đầu Mèo MX 1U
Dùng để làm gì Bộ bốn keycap nghệ thuật gồm hai mẫu bàn chân mèo và hai mẫu đầu mèo, tạo hình bo tròn mượt với chi tiết nổi 3D. Các keycap dùng chân gắn Cherry MX chuẩn, đáy rỗng và thành dày 1,6 mm, phù hợp với bàn phím cơ dùng switch Cherry MX. Mỗi chiếc có hình nổi ở màu tương phản; mắt và mũi của mẫu đầu mèo nhô cao hơn bề mặt. Gồm 4 keycap: 2 bàn chân mèo và 2 đầu mèo. Màu xen kẽ hồng pastel và trắng. Tương thích chân gắn Cherry MX, chuẩn kích thước 1U. Kích thước Đáy: 17,8 mm. Mặt trên: 16 mm. Chiều cao thân: 9 mm; điểm nổi cao nhất: 10,4 mm. Thành dày 1,6 mm, đáy rỗng. Bốn keycap được bố trí cách nhau 22 mm trên mặt in. Mặt trên thu nhỏ còn 16 mm thay vì 18 × 18 mm để keycap giữ dáng thuôn và không chạm vào phím bên cạnh ở khoảng cách phím 18 mm. Gợi ý biến tấu Phối lại thứ tự hồng pastel và trắng giữa bàn chân và đầu mèo. Thêm tên hoặc ký tự nổi trên mặt keycap để làm bộ phím cá nhân hóa. Tạo thêm biến thể bàn chân trái và bàn chân phải để ghép thành cặp đối xứng. In ấn Bộ được bố trí thành một mô hình chung, không cần lắp ráp. Có thể tách từng keycap khi chuẩn bị in nếu muốn in riêng từng màu hoặc từng mẫu.
Fidget toy à trois engrenages et boutons
Fidget toy mécanique compact, imprimable en PLA sans supports, sans ressort métallique ni pièce achetée. Les trois engrenages sont en prise : en tourner un entraîne les deux autres. Chacun porte une molette à encoches sur le dessus, et le troisième clique contre une languette flexible imprimée avec la base. Les engrenages tournent sur des axes séparés qui se clipsent par le dessus dans la base. Chaque roue repose à 0,5 mm au-dessus de la base et est retenue par la tête de son axe. Les trois boutons poussoirs se clipsent eux aussi par le dessus et se verrouillent avec un clic en position haute et en position basse. Base arrondie de 50 × 50 mm, hauteur totale 17 mm Engrenages de 14, 10 et 12 dents, module 1,5, jeu entre dents de 0,4 mm 3 axes clipsables, pied fendu avec ergot, jeu de 0,3 mm dans la roue 3 boutons avec 2 mm de course et deux crans de maintien Languette de cliquet imprimée avec la base Pièces à imprimer séparément : base, 3 engrenages, 3 axes, 3 boutons
Skeletal — Open-Frame Solar Tracker
Skeletal is a minimal-plastic, screw-free single-axis solar tracker: an open-frame base, a snap-in SG90 servo holder, a rotating platform and a ribbed mock solar panel, with a front bracket that holds two LDRs behind a central divider. Features 1.2 mm walls and an open-frame base to keep filament use low Servo holder with small chamfered snap lugs that grip the SG90 body, so it clicks in and pulls out without tools Cable slot from the base up to the rotating platform Panel centred on the rotation axis, with a raised rim, cell lines and a light ribbed underside Two LDR openings with a vertical divider in the front sensor bracket Print notes Printed flat in PLA, 0.4 mm nozzle, 0.2 mm layers Nano, SG90, horn and LDR dimensions are nominal. Measure the real parts and adjust the values at the top before printing.
Phone Stand with Cable Channel
A phone stand that holds the phone upright in portrait or landscape, with a cable channel so the charger doesn't pin the phone down or dangle off the edge. Most stands either tip the phone back too far to tap or force the cable to loop around the outside. This one leans the phone at 70° from horizontal and routes the cable up through the stand to the back of the phone. What decides fit and print Lean angle: 70° from horizontal, steep enough to tap the screen and upright enough to watch video. Groove: runs the full 90 mm width, so the phone sits in it in either orientation. It is sized for a phone in a thin case. Cable channel: 12 mm wide, open on the underside of the base. It runs in from the back, then rises through a 12 x 12 mm opening in the groove floor. Overall size: 90 mm wide, about 56 mm deep and 70 mm tall. Printing: the flat base goes down on the bed. The underside channel is a 7 mm-tall tunnel, so print it with bridging on or light supports. No other supports are needed. Material: PLA or PETG both work. Use 3 or more perimeters for a stiffer groove lip.