30° Tilted Stand for 118x84mm Keypad
Created today
Description
Wedge-style desk stand that holds a 118x84mm macro keypad at a 30° tilt, so the keys face the user instead of lying flat. The pad sits in a recessed pocket that grips its base on all four sides to stop it creeping during use.
A finger notch at the front edge lets the pad be lifted out. A cable slot at the back edge routes the cord away from the desk surface.
Specs
- Pad size: 118 x 84 mm
- Pocket clearance: 0.3 mm per side (0.6 mm total on each axis)
- Tilt angle: 30°
- Overall footprint: about 124 x 80 mm, roughly 53 mm tall at the rear
- Wall thickness: 2.5 mm
- Front notch: 40 mm wide finger cut-out for lifting the pad
- Cable slot: 24 mm wide, centered on the back edge
- Underside: flat; add rubber feet or tape for grip on smooth desks
- Print orientation: flat side down, no supports needed
Notes
- Check the pocket depth and cable slot position against the actual pad before printing.
- If the cable exits somewhere other than the center of the back edge, the slot position needs to be moved.
Photos
Technical views
More like this
Explore more in Desk & Tech →
Samsung S24 FE Snap-In Bumper Case
A one-piece snap-in bumper case for the Samsung S24 FE, sized from the 162.0 × 77.3 × 8.0 mm phone spec with 0.2 mm clearance. The open front leaves the screen clear, and the walls are 1.8 mm with a 1.5 mm back and a 1.2 mm lip that catches the screen edge. Camera cutout on the back Button slot along one side Bottom slot for USB-C and the speaker Prints back-down with no supports One piece, no assembly The case is rigid, so the phone presses in from one corner. PLA works, but a flexible filament such as TPU is easier on the phone and less likely to crack the lip. The camera and button positions are estimates, so check them against your phone before printing the whole case.
ReplixHD Gaming Cable Holder.
A low, slate-like desk plate in the spirit of a game-console accessory, with three rounded C-shaped clips standing in a symmetrical row. Cables press in from above, sit in a 4.4 mm round channel, and are held by smooth lips. Size: 60 × 20 mm, 5 mm base, 7 mm total height. Clips: three, 17 mm apart, 3.6 mm entry opening, lips about 1.2 mm thick at the opening. Floor: about 1.8 mm of material under each channel, measured from the tape recess. Underside: 48 × 12 mm tape recess, 0.5 mm deep. Printing: one solid piece, flat bottom, no supports needed.
Desk Clamp Headphone Holder, 15–35 mm
What it's for A two-piece headphone holder that clamps to a desk edge and holds headphones on an upper hook arm. A threaded screw with a large knob under the lower jaw tightens it. Dimensions Desk thickness range: 15–35 mm Width: 40 mm Body height: about 69 mm Hook reach: 55 mm past the spine, with a raised lip Screw: 10 mm diameter, 3 mm pitch, 26 mm pad, 32 mm knob Print notes Two parts: clamp body and screw Print the body on its side (40 mm face down) and the screw upright, both without supports PLA, 4 or more perimeters Remix ideas Add a rubber or felt pad to the screw head Lengthen the hook arm for larger headphones Add a cable notch on the lip
Card Press met Schroefdop
Een persbakje voor Pokémon-kaarten, bestaand uit vier losse printdelen: een bakje, een persplaat, een draaischroef en een schroefdop. Het bakje is dicht aan de achter- en zijkanten, heeft een vingeruitsparing aan de voorkant en een brug met schroefdraad over de bovenkant. De plaat ligt op de kaarten en heeft een ronde inzinking in het midden. De draaischroef zet de plaat onder druk. De schroefdop draait op de punt van de schroef en heeft een ronde voet die in de inzinking past. Binnenruimte bakje: 68 × 93 mm Schroefdraad: 14 mm, spoed 3 mm Inzinking in de plaat: 16 mm doorsnede Schroefdop: 15 mm voet, 22 mm doorsnede Print de dop met de voet naar beneden, zonder support
Tiny Keycap Set For Tact Switches
A sheet of 59 miniature round keycaps in the spirit of a tiny typewriter keyboard, sized to dress up tactile switches. Each cap is 5 mm across and 1.6 mm thick, with a short 3 mm glue post and an engraved legend: letters, digits, arrows and common symbols. 26 letters A–Z and digits 0–9 Four arrow caps (right, up, left, down) 19 common symbols 3 mm post, 1.4 mm tall, for gluing to the switch Printed face-down, so no supports are needed Use a fine layer height (0.2 mm or less) so the small engraved glyphs stay legible.
Desk Holder for 6 USB Sticks
A solid block with six angled slots that keeps USB-A sticks upright on the desk instead of loose in drawers. Each slot leans back 30 degrees, so labels on the sticks face a person seated at the desk. Each slot is sized for a standard USB-A stick with a little room to spare, and the slots are separated by 2.5 mm dividers. The outer edges have a small chamfer, and the base sits flat on the bed with no supports needed. Capacity: 6 USB-A sticks Slot size: 13 mm wide, 6 mm deep Slot angle: 30 degrees tilted back Divider thickness: 2.5 mm Overall size: about 95 mm long, 19 mm deep, 30 mm tall Print orientation: flat on its base, no supports