Samsung S24 FE Snap-In Bumper Case
Created today
Description
A one-piece snap-in bumper case for the Samsung S24 FE, sized from the 162.0 × 77.3 × 8.0 mm phone spec with 0.2 mm clearance. The open front leaves the screen clear, and the walls are 1.8 mm with a 1.5 mm back and a 1.2 mm lip that catches the screen edge.
- Camera cutout on the back
- Button slot along one side
- Bottom slot for USB-C and the speaker
- Prints back-down with no supports
- One piece, no assembly
The case is rigid, so the phone presses in from one corner. PLA works, but a flexible filament such as TPU is easier on the phone and less likely to crack the lip. The camera and button positions are estimates, so check them against your phone before printing the whole case.
Images
More like this
Explore more in Desk & Tech →
ReplixHD Gaming Cable Holder.
A low, slate-like desk plate in the spirit of a game-console accessory, with three rounded C-shaped clips standing in a symmetrical row. Cables press in from above, sit in a 4.4 mm round channel, and are held by smooth lips. Size: 60 × 20 mm, 5 mm base, 7 mm total height. Clips: three, 17 mm apart, 3.6 mm entry opening, lips about 1.2 mm thick at the opening. Floor: about 1.8 mm of material under each channel, measured from the tape recess. Underside: 48 × 12 mm tape recess, 0.5 mm deep. Printing: one solid piece, flat bottom, no supports needed.
Desk Clamp Headphone Holder, 15–35 mm
What it's for A two-piece headphone holder that clamps to a desk edge and holds headphones on an upper hook arm. A threaded screw with a large knob under the lower jaw tightens it. Dimensions Desk thickness range: 15–35 mm Width: 40 mm Body height: about 69 mm Hook reach: 55 mm past the spine, with a raised lip Screw: 10 mm diameter, 3 mm pitch, 26 mm pad, 32 mm knob Print notes Two parts: clamp body and screw Print the body on its side (40 mm face down) and the screw upright, both without supports PLA, 4 or more perimeters Remix ideas Add a rubber or felt pad to the screw head Lengthen the hook arm for larger headphones Add a cable notch on the lip
iPhone 13 Pro Max Case with Awareness Ribbon Inlay
What it's for A purple case for the iPhone 13 Pro Max with a peach cancer awareness ribbon inlaid flush into the back. The ribbon sits in a matching recess as a separate 1.2 mm-thick inlay, so you can print it in a second color or change filament at that layer. The screen side is open with a small lip to hold the phone, and the back has a rounded 40 mm camera cutout. It has not been test-fitted on a physical phone. Dimensions Case footprint on the print plate: 83.1 × 165.8 × 10 mm. Phone cavity: 78.7 × 161.4 mm, with 2.2 mm walls and a 1.6 mm back. Peach ribbon inlay: 32 × 49.3 mm, 1.2 mm thick. Camera cutout: 40 mm rounded opening at the top corner of the back. Print the case back-down. Remix ideas Change the ribbon color for another awareness cause while keeping the flush recess. Resize or reshape the ribbon inlay, or add a short message alongside it. Add button cutouts or adjust the front lip for a different fit preference.
Nothing Phone (1) Case with Flipper Zero Cradle
A snap-on case for the Nothing Phone (1) with an integrated cradle on the back for a Flipper Zero. The phone enters from the screen side and is held by a 1.5 mm lip, while side-button slots and a bottom opening keep the buttons, USB-C port and speaker clear. The cradle sits on the lower two-thirds of the back, clear of the camera, and holds the Flipper Zero with snap ridges and finger notches. Corners on both the case and the cradle are rounded generously for a softer outline. Specs Phone fit: Nothing Phone (1); open front with a 1.5 mm retaining lip; side-button slots; USB-C and speaker opening. Back window: opening over the camera and glyph area. Flipper cradle: lower two-thirds of the back; 13 mm pocket height; port slots at both ends; finger notches on the long sides; snap ridges to hold the Flipper Zero. Flipper clearance: the Flipper Zero is 25 mm thick, so about half of it sits above the cradle rim. Corners: case outline 11 mm radius, cradle 10 mm radius; pockets and screen opening rounded to match; the cradle rim's top edges are still square. Overall size: the case is about 80 mm wide and 164 mm tall; the cradle is about 46 mm wide and 106 mm tall. Wireless charging: the cradle covers the phone’s wireless-charging area. Printing: print screen-side down with the cradle opening facing up. TPU is recommended for the 1.5 mm lip; PLA makes the lip stiff. Print status: this version has not been test-printed.
Case ESP32 + LoRa com Cooler
Case compacto para ESP32 e módulo LoRa SX1278, com compartimento para um cooler de 30 mm e tampa de encaixe sem parafusos. A entrada de ar do cooler fica no piso, sob uma capa em grade, e a parede +X é lisa. Ganchos para remix Entrada de ar: abertura de 25 mm no piso, sob a grade. Dá para trocar por outro desenho de grade ou reabrir fendas na parede +X. Cooler: centrado em x = 48, furação de 24 mm (furos de 2,8 mm). Ajuste se o seu for de outra medida. Apoios do ESP32: quatro pinos com furo M2, em x = ±22 e y = ±9. Confira com a sua placa. Prateleira do LoRa: trilhos de 20 mm, 3 mm de largura, 2 mm de altura. Aumente se a placa balançar. Combina com: texto na tampa ("Altear AgroGuard") e na lateral ("Altear Tech"), trocáveis por outros nomes. Dimensões externas: 98 × 34 mm, altura de 24 mm mais a tampa de 6 mm.
C-Shaped Lamp Sleeve With Slots
A single-piece C-channel sleeve that slides onto a 120 x 40 mm, 12 mm thick LED lamp panel and blocks light except through three evenly spaced slots. The front plate and side walls are 2.4 mm thick, enough to be opaque in PLA. Back lips hold the panel in place, and the cavity has 0.2 mm clearance per side for a sliding fit. Two 6 mm bridges at the ends keep the strips between the slots connected. Cavity: 120.4 x 12.4 mm Slots: three, 6 x 40 mm, equal spacing Sleeve length: 52 mm Prints in one piece, front face down, no supports needed for the walls Fits the Bambu A1 mini bed