Desk Holder for 6 USB Sticks
Created today
Description
A solid block with six angled slots that keeps USB-A sticks upright on the desk instead of loose in drawers. Each slot leans back 30 degrees, so labels on the sticks face a person seated at the desk.
Each slot is sized for a standard USB-A stick with a little room to spare, and the slots are separated by 2.5 mm dividers. The outer edges have a small chamfer, and the base sits flat on the bed with no supports needed.
- Capacity: 6 USB-A sticks
- Slot size: 13 mm wide, 6 mm deep
- Slot angle: 30 degrees tilted back
- Divider thickness: 2.5 mm
- Overall size: about 95 mm long, 19 mm deep, 30 mm tall
- Print orientation: flat on its base, no supports
Photos
Technical views
More like this
Explore more in Desk & Tech →
Phone Stand with Cable Channel
A phone stand that holds the phone upright in portrait or landscape, with a cable channel so the charger doesn't pin the phone down or dangle off the edge. Most stands either tip the phone back too far to tap or force the cable to loop around the outside. This one leans the phone at 70° from horizontal and routes the cable up through the stand to the back of the phone. What decides fit and print Lean angle: 70° from horizontal, steep enough to tap the screen and upright enough to watch video. Groove: runs the full 90 mm width, so the phone sits in it in either orientation. It is sized for a phone in a thin case. Cable channel: 12 mm wide, open on the underside of the base. It runs in from the back, then rises through a 12 x 12 mm opening in the groove floor. Overall size: 90 mm wide, about 56 mm deep and 70 mm tall. Printing: the flat base goes down on the bed. The underside channel is a 7 mm-tall tunnel, so print it with bridging on or light supports. No other supports are needed. Material: PLA or PETG both work. Use 3 or more perimeters for a stiffer groove lip.
Organischer Kopfhörerständer in Rosa
Kopfhörerständer mit breitem, abgerundetem Bogen, geschwungenen, sich kreuzenden Streben und einer flachen, wellenförmigen Standfläche. Ein zusammenhängender Körper, flach druckbar, gedacht für pastellrosa PLA. Remix-Ansatz Bogen: Außenradius 65 mm, Strebenbreite 22 mm. Größerer Radius für breitere Kopfbügel. Streben: Vier Kurven, Kontrollpunkte frei verschiebbar für andere Öffnungen. Basis: ca. 224 × 150 mm, 8 mm hoch. Dicker oder mit Gewicht-Einlage für mehr Standsicherheit. Tiefe der Streben: 36 mm, anpassbar. Gesamthöhe ca. 260 mm.
StudyDock Desktop Phone Stand
What it's for A one-piece desktop phone stand for students, holding a phone at a 65° viewing angle on a desk. Dimensions 65 mm wide, 75 mm deep, 70 mm tall 4 mm flat base, 4–5 mm walls 14 mm deep shelf with a 6 mm front lip Two triangular side supports Remix ideas Widen the shelf for phones with cases. Add a cable slot through the backrest. Lower the backrest angle for typing-height viewing.
Snake Tail Phone Stand
A one-piece orange phone stand with a low front lip, a short flat seat and a backrest leaning up to about 60 mm. A zig-zag snake of humps runs along the back. Remix hooks Lip height: the front stopper is about 5 mm of strip plus the strip's rounded end, roughly 7.5 mm in total. Raise it for a more secure hold, or lower it further to keep captions clear. Seat depth: 12 mm. Deepen it for thick cases, though a steeper backrest helps more. Backrest angle and height: it rises about 18 mm in Y over 55 mm in Z, so it is steep. Both are easy to change. Snake humps: 4 peaks, each about 14 mm high. Add more humps, or raise or lower the peaks. Width: 70 mm, with a 5 mm strip thickness. Pairs well with a non-slip pad on the seat.
90mm USB Fan Guard Cloth Comb Clip
A cloth-hanging clip for the wire guard of a small USB desk fan, roughly 90 mm across. It holds a damp cloth in front of the grille so the airflow picks up moisture and cools a little as it passes, a basic evaporative cooler for a desk. What it fits Small USB fans with a wire or rim guard around 90 mm across. Damp cloths, such as a thin cotton towel or tea towel, pinched along one edge. What it does Rear arm at Y=0 sits on the guard side. A 30 mm deep spine runs across the top. Front arm at Y=27–30 hangs the cloth side. Eleven thin fingers, 2.4 mm wide and pitched at 5.4 mm, pinch the cloth edge so it hangs flat instead of bunching. Overall size: 60 mm wide, 30 mm deep, 22 mm tall. Check before printing Guard wire or rim thickness. No slot is sized to a specific wire yet. Measure the guard wire or rim and adjust the gap before relying on the grip. Cloth standoff. The cloth sits about 27 mm from the guard-side arm, not the 15 mm originally targeted. Shorten the spine if the cloth needs to sit closer. Known incompatibilities Not intended for fans with a solid or thick moulded frame in place of a wire guard. Not tested against any particular fan model. Verify the guard dimensions first. Keep the cloth damp, not dripping, and keep water and wet cloth away from USB connections and the fan's electronics.
Bridge-Style Monitor Riser With Pen Lip
A low viaduct for your desk: a flat 500 mm span carried on two slab-sided legs, lifting the monitor 80 mm and leaving a wide open tunnel underneath. A low profile keyboard slides straight in and out, and a thin lip along the back edge works as a curb so pens and pencils stop rolling off the far side. Design notes Footprint: 500 mm wide by 240 mm deep. Shelf height: the top surface sits 80 mm above the desk, with a 15 mm thick shelf and chamfered edges. Keyboard clearance: about 65 mm of open height between the legs, comfortably above the 35 mm minimum requested. Gap between legs: roughly 460 mm, enough for a full-size keyboard with room to spare. Back lip: 3 mm thick and rising 6 mm above the shelf, running the full width. Print note: at 500 mm wide it exceeds most print beds, so it suits a large-format printer or a split into joined sections. Pairs well with A cable clip or grommet added along the back for monitor leads. Non-slip pads under the legs to keep the bridge planted.