Tiny Keycap Set For Tact Switches
Created today
Description
A sheet of 59 miniature round keycaps in the spirit of a tiny typewriter keyboard, sized to dress up tactile switches. Each cap is 5 mm across and 1.6 mm thick, with a short 3 mm glue post and an engraved legend: letters, digits, arrows and common symbols.
- 26 letters A–Z and digits 0–9
- Four arrow caps (right, up, left, down)
- 19 common symbols
- 3 mm post, 1.4 mm tall, for gluing to the switch
- Printed face-down, so no supports are needed
Use a fine layer height (0.2 mm or less) so the small engraved glyphs stay legible.
Images
More like this
Explore more in Desk & Tech →
Frostmourne Fantasy Sword Sculpture
A detailed gothic fantasy sword sculpture, laid flat on the print plate with the handle on the left and the blade pointing right. The pommel underside and the guard spikes are trimmed flush so the whole sword rests on the plate at z=0, which makes it sit stable while printing and lets it lie flat as a display piece. The blade runs about 157 mm long with a beveled, notched double edge, rune cuts down the middle and a thin central groove. The crossguard is the widest point at roughly 101 × 76 mm, built as a central block with curved horns, an upper horn, a rear spike and a forward spike. The grip is a core wrapped in raised rings, and the pommel carries a collar, radial spikes and a tail spike. Everything is modelled as one connected solid with the deep relief, sharp edges and layered ornament of the original design. Blade, crossguard and wrapped grip as one connected piece Beveled double edge with sculpted runes and a centre groove Curved horn crossguard with rear and forward spikes Round pommel with collar, radial spikes and tail spike Pommel and guard spike tips trimmed flat to sit on the plate Prints in millimeters; the thinnest spike tips taper down to about 1.5 mm The thin spike tips are the fragile part of the model — handle them carefully when removing the print, and thicken them if you want a sturdier piece.
Gothic Frostmourne 2U Backspace Keycap
A 2U backspace keycap with a rounded rectangular body, hollow underside and cross stem. The top carries a raised gothic relief: a Frostmourne-style sword runs horizontally with the grip at left and the blade at right, four sculpted skulls sit in the corners, and rows of gothic spikes frame the top and bottom edges around a central diamond ornament. The cap measures 37 × 18 mm with an 8 mm body; the sword relief reaches 3.9 mm, the gothic spikes 4.1 mm and the skulls 2.3 mm. Note: no stabilizer slots are included, so check whether the 2U backspace position on your board needs them before printing. Remix hooks Sword depth: The sword is the tallest relief at 3.9 mm. Raise or flatten it to trade drama for a lower-profile cap. Skull scale: The corner skulls are 2.3 mm tall; enlarge them or simplify the teeth if your printer struggles at this scale. Frame density: The gothic spikes are 4.1 mm tall and define the outer silhouette. Thin them, space them wider, or swap the central diamond for another ornament. Body fit: 37 × 18 mm and an 8 mm body are the starting values. Adjust skirt height, dish depth or stem clearance to suit your board, and add stabilizer slots if needed. Variants: Try a smoother stone background, a single central skull, or a mirrored sword for a different corner balance. The cap pairs naturally with other dark-fantasy keycaps as a statement backspace.
Bộ Keycap Bàn Chân Và Đầu Mèo MX 1U
Dùng để làm gì Bộ bốn keycap nghệ thuật gồm hai mẫu bàn chân mèo và hai mẫu đầu mèo, tạo hình bo tròn mượt với chi tiết nổi 3D. Các keycap dùng chân gắn Cherry MX chuẩn, đáy rỗng và thành dày 1,6 mm, phù hợp với bàn phím cơ dùng switch Cherry MX. Mỗi chiếc có hình nổi ở màu tương phản; mắt và mũi của mẫu đầu mèo nhô cao hơn bề mặt. Gồm 4 keycap: 2 bàn chân mèo và 2 đầu mèo. Màu xen kẽ hồng pastel và trắng. Tương thích chân gắn Cherry MX, chuẩn kích thước 1U. Kích thước Đáy: 17,8 mm. Mặt trên: 16 mm. Chiều cao thân: 9 mm; điểm nổi cao nhất: 10,4 mm. Thành dày 1,6 mm, đáy rỗng. Bốn keycap được bố trí cách nhau 22 mm trên mặt in. Mặt trên thu nhỏ còn 16 mm thay vì 18 × 18 mm để keycap giữ dáng thuôn và không chạm vào phím bên cạnh ở khoảng cách phím 18 mm. Gợi ý biến tấu Phối lại thứ tự hồng pastel và trắng giữa bàn chân và đầu mèo. Thêm tên hoặc ký tự nổi trên mặt keycap để làm bộ phím cá nhân hóa. Tạo thêm biến thể bàn chân trái và bàn chân phải để ghép thành cặp đối xứng. In ấn Bộ được bố trí thành một mô hình chung, không cần lắp ráp. Có thể tách từng keycap khi chuẩn bị in nếu muốn in riêng từng màu hoặc từng mẫu.
Desk Holder for 6 USB Sticks
A solid block with six angled slots that keeps USB-A sticks upright on the desk instead of loose in drawers. Each slot leans back 30 degrees, so labels on the sticks face a person seated at the desk. Each slot is sized for a standard USB-A stick with a little room to spare, and the slots are separated by 2.5 mm dividers. The outer edges have a small chamfer, and the base sits flat on the bed with no supports needed. Capacity: 6 USB-A sticks Slot size: 13 mm wide, 6 mm deep Slot angle: 30 degrees tilted back Divider thickness: 2.5 mm Overall size: about 95 mm long, 19 mm deep, 30 mm tall Print orientation: flat on its base, no supports
Platinenabdeckung 20x20 mm mit Öse
Abdeckung für eine 20×20×4 mm große D-förmige Platine mit Einrastnasen, Tasteröffnung und Schnuröse an der Rundung. Gesamthöhe 7,8 mm, Decke 0,8 mm, Wandstärke 1,8 mm Tasteröffnung 3,8 × 3,8 mm Öse: 6,5 mm Außendurchmesser, 3,2 mm Bohrung, 2 mm dick, bündig mit der Oberseite Öse sitzt mittig an der Rundung (Y = 0) auf der +X-Seite Empfohlen: transparentes PETG oder PLA
iPhone 17 Pro Max Hülle mit Kameraausschnitt
Massive Schutzhülle für das iPhone 17 Pro Max: 4 mm Wände, 3 mm Rückseite und eine 3 mm breite Frontlippe, die höher über das Display steht. Kameraausschnitt, Öffnungen für die Seitentasten und eine Öffnung unten für den Anschluss sind vorgesehen. Die Hülle wird in einem Stück gedruckt. Auf der Druckplatte misst das Teil etwa 86,6 × 172 × 15,1 mm. Auf der Rückseite ist ein eigenes Logo eingraviert: ein Doppelring mit „09“ in der Mitte, umlaufen vom Bogen-Schriftzug „BORUSSIA DORTMUND“. Die Gravur ist etwa 66 mm breit und 1 mm tief. Von hinten gesehen ist sie lesbar und sitzt unter dem Kameraausschnitt. Bei 3 mm Rückseite bleiben 2 mm Material unter der Gravur. Es ist kein offizielles Vereinswappen. Passt für iPhone 17 Pro Max (Gehäuse 163,4 × 78 × 8,75 mm; die Hülle ist mit etwas Spiel darauf ausgelegt) Vor dem Drucken prüfen Die Lage der Kamera- und Tastenausschnitte ist geschätzt und nicht an einem echten Gerät kontrolliert. Miss vor dem Druck die Positionen an deinem Gerät nach und verschiebe die Ausschnitte bei Bedarf. Durch die dickeren Wände sind die Tastenöffnungen tiefer; die Tasten lassen sich dadurch schwerer drücken. Prüfe, ob das für dich noch passt. Für den Bau ist TPU statt PLA sinnvoller, weil es Stöße besser abfedert. Passt nicht Andere iPhone-Modelle, auch nicht die früheren Pro-Max-Größen mit anderem Gehäusemaß.