Downloaded 17 times
Description
A freestanding, bold typographic nameplate cut in Archivo Black. Set flush to the build plate at a clean 2 mm thickness, this design drops the traditional backplate entirely for a minimalist, letter-only look.
Print notes
- Pieces: Prints as separate letters (no overlapping or connecting structures)
- Thickness: 2.0 mm flat extrusion
- Build Plate Adhesion: High surface area allows for easy bed adhesion without brims
Images
More like this
Explore more in Keychains & EDC →
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
35 mm Threaded Keychain Container, Rosette Lid
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
Pin de mano esquelética con dedo medio levantado
Pin con forma de mano esquelética cerrando el puño y con el dedo medio levantado. El dedo medio sube recto con sus tres falanges; el índice, el anular y el meñique quedan plegados hacia la palma. El pulgar va por detrás de los dedos plegados, así que solo asoma por el lado izquierdo y entre los huesos. Los huesos son blancos y de estilo realista: cada uno tiene una diáfisis fina y dos cóndilos redondeados en cada extremo, con una muesca central, y el extremo superior algo más pequeño. Las divisiones negras entre huesos marcan las articulaciones. En la palma hay cuatro metacarpianos y en la muñeca un grupo de huesos del carpo pequeños. La placa negra de 2 mm sigue la silueta de la mano y sobresale como borde. Los huesos van elevados 0,9 mm sobre ella, con la parte trasera completamente plana. La pieza mide unos 23 × 36 mm, así que queda 1 mm por encima de los 35 mm; el grosor total es de unos 2,9 mm. Para ajustarla al límite de 35 mm, reduce el borde de la placa. Placa negra plana de 2 mm; huesos blancos elevados 0,9 mm Huesos segmentados y separados por huecos negros de articulación, todos apoyados en la placa Sin piezas flotantes; se imprime como una sola pieza Sin soportes: la parte trasera es plana y los detalles se elevan desde la placa Huecos estrechos entre huesos; pensados para una boquilla de 0,4 mm
21mm Disk Holder with Snap Lip
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge
Portachiavi Famiglia Raganella con rilievo
Il portachiavi a raganella risolve il momento in cui tutte le chiavi di casa sembrano la stessa copia e si finisce a provarle una per una. La rana e la scritta FAMIGLIA RAGANELLA restano in rilievo sulla piastra, mentre le zampe anteriori e posteriori sono state abbassate fino a fondersi con il portachiavi: non restano sospese sopra la piastra e non sporgono come elementi separati. Misure e stampa Set da cinque portachiavi: ingombro 194 × 52 mm sul piano di stampa Piastra singola: 34 × 44 mm, spessore 3 mm Foro per l'anello: 5 mm Rana e scritta in rilievo, circa 1 mm sopra la piastra Zampe anteriori e posteriori fuse alla piastra Stampa piatta, senza supporti, anche in PLA
Fanlock — 6-Key Pivot Organiser
Fanlock is a compact pivot organiser that stacks up to six keys between two side plates on a single bolt. Keys fan out when needed and stay put when closed, so they stop jingling and stop wearing through pockets. The nut sets the tension, so keys can be held at whatever angle they are swung to. The plates are 75 mm long, sized for house keys, with a tapered free end and a rounded pivot end. One plate has a round recess that hides the bolt head. The other has a hex recess that captures the nut. Both sit flush with the outer faces. Seven thin spacers keep the keys from rubbing on each other or on the plates. Dimensions Plate length: 75 mm Plate width at the pivot: 20 mm Plate thickness: 4 mm Pivot hole: 5.5 mm, set 8 mm from the end Spacers: 10 mm outer diameter, 0.6 mm thick, 7 included Second 4 mm hole near the free end of each plate, for a lanyard or split ring In the box 1 head-side plate 1 nut-side plate 7 spacers Hardware needed 1 × M5 × 25 mm bolt 1 × M5 nut Print notes All pieces print flat with no supports. The stack assumes keys about 2 mm thick. Six keys, seven spacers and two plates come to roughly 24 mm, which leaves very little thread past the nut. With thicker keys, switch to an M5 × 30 mm bolt.