Caja en cuña parte dcha borde ancho

Marco para Tablet de 11 Pulgadas

Marco rígido con ventana frontal para una tablet de 11 pulgadas. La tablet se desliza desde el lado superior y queda sujeta por los labios delantero y trasero. What it's for Mantener una tablet de 11" enmarcada, para pared o escritorio, dejando la pantalla visible y la parte trasera abierta. Dimensions Exterior: 265 × 196 × 11,5 mm Hueco interior: 249 × 180 × 7 mm (tablet tipo 247,6 × 178,5 × 5,9 mm) Ventana frontal y trasera: 229 × 160 mm Ranura de inserción en el lado superior Remix ideas Añadir orificios de colgado en la parte trasera. Ajustar el hueco a tu modelo exacto. Añadir un soporte trasero inclinado.

6 hours agoRemix →

iPhone 17 Pro Max Hülle mit Kameraausschnitt

Massive Schutzhülle für das iPhone 17 Pro Max: 4 mm Wände, 3 mm Rückseite und eine 3 mm breite Frontlippe, die höher über das Display steht. Kameraausschnitt, Öffnungen für die Seitentasten und eine Öffnung unten für den Anschluss sind vorgesehen. Die Hülle wird in einem Stück gedruckt. Auf der Druckplatte misst das Teil etwa 86,6 × 172 × 15,1 mm. Auf der Rückseite ist ein eigenes Logo eingraviert: ein Doppelring mit „09“ in der Mitte, umlaufen vom Bogen-Schriftzug „BORUSSIA DORTMUND“. Die Gravur ist etwa 66 mm breit und 1 mm tief. Von hinten gesehen ist sie lesbar und sitzt unter dem Kameraausschnitt. Bei 3 mm Rückseite bleiben 2 mm Material unter der Gravur. Es ist kein offizielles Vereinswappen. Passt für iPhone 17 Pro Max (Gehäuse 163,4 × 78 × 8,75 mm; die Hülle ist mit etwas Spiel darauf ausgelegt) Vor dem Drucken prüfen Die Lage der Kamera- und Tastenausschnitte ist geschätzt und nicht an einem echten Gerät kontrolliert. Miss vor dem Druck die Positionen an deinem Gerät nach und verschiebe die Ausschnitte bei Bedarf. Durch die dickeren Wände sind die Tastenöffnungen tiefer; die Tasten lassen sich dadurch schwerer drücken. Prüfe, ob das für dich noch passt. Für den Bau ist TPU statt PLA sinnvoller, weil es Stöße besser abfedert. Passt nicht Andere iPhone-Modelle, auch nicht die früheren Pro-Max-Größen mit anderem Gehäusemaß.

6 days agoRemix →

Nested Condensation Coaster with Removable Basin Insert

What it's for A two-part coaster for a glass or mug on a desk. The cup rests flat on the raised platform of the removable insert — nothing is inserted into a sleeve or ringed by walls — and condensation running down the glass collects in the basin around the platform. The outer shell is a second, watertight barrier that catches anything the insert lets past, and there are no drainage holes or outlets anywhere, so the water stays put until the insert is lifted out and emptied. The two parts print separately and can be cleaned separately. Outer Containment Shell — one continuous watertight body, open at the top so the inside is fully accessible with the insert out. Four integrated pillars support the insert. Inner Insert — raised cup platform, recessed collection basin, and a groove in the platform floor for a removable silicone grip ring. Support pillars — four 8 mm round pillars, 90° apart on a 58 mm radius, rising from the shell floor to hold the insert 3.5 mm clear of the bottom. Silicone provisions — a grip-ring groove in the recess floor and four pockets underneath the shell for non-slip feet. The silicone parts themselves are not printed. Dimensions Outer shell: 148 mm diameter, 22 mm tall, 2.4 mm walls, 3 mm base. Inner insert: 141.8 mm diameter, 13.5 mm tall, sitting 3.5 mm above the shell floor with 0.7 mm clearance per side. Cup platform: 95 mm diameter, top surface at 19 mm height. Locating recess: 80 mm diameter, 1 mm deep, in the platform top. Grip-ring groove: 1.5 mm deep, between 34 and 37 mm radius, in the recess floor. Basin: about 24 mm wide and roughly 10.5 mm deep at the wall, holding approximately 55–65 ml before it overflows into the shell. Foot pockets: four at 10 mm, 1 mm deep, on a 58 mm radius circle, directly below the pillars. Print notes Print both parts in PETG with four or more perimeters — the shell's wall seal is what keeps the desk dry. The shell's foot pockets stop short of the inside floor, so the base stays closed. Watch first-layer elephant foot on the shell's outer base edge; it can make the part rock. The shell rim stands 2 mm above the insert, and the space under the insert adds further secondary containment, so overflow is caught. The pillars print flat-bottomed with no supports, and the open gap under the insert allows inspection and drying after use. Remix ideas Add a lift tab or finger notch to the insert rim — as it stands the tight gap means a wet insert may need a thumbnail or thin tool to lift, though the open underside helps. Add a small locating dimple to the insert underside to stop it sliding its 0.7 mm of play. Widen the platform for larger mugs; cups wider than 95 mm overhang the platform and drip into the basin, which works but is less stable. Increase the insert height or basin depth if you want more collection capacity. Swap the four-pocket foot pattern for a continuous silicone band if the coaster lives on a slippery surface.

just nowRemix →

Case ESP32 + LoRa com Cooler

Case compacto para ESP32 e módulo LoRa SX1278, com compartimento para um cooler de 30 mm e tampa de encaixe sem parafusos. A entrada de ar do cooler fica no piso, sob uma capa em grade, e a parede +X é lisa. Ganchos para remix Entrada de ar: abertura de 25 mm no piso, sob a grade. Dá para trocar por outro desenho de grade ou reabrir fendas na parede +X. Cooler: centrado em x = 48, furação de 24 mm (furos de 2,8 mm). Ajuste se o seu for de outra medida. Apoios do ESP32: quatro pinos com furo M2, em x = ±22 e y = ±9. Confira com a sua placa. Prateleira do LoRa: trilhos de 20 mm, 3 mm de largura, 2 mm de altura. Aumente se a placa balançar. Combina com: texto na tampa ("Altear AgroGuard") e na lateral ("Altear Tech"), trocáveis por outros nomes. Dimensões externas: 98 × 34 mm, altura de 24 mm mais a tampa de 6 mm.

3 hours agoRemix →

Samsung S24 FE Snap-In Bumper Case

A one-piece snap-in bumper case for the Samsung S24 FE, sized from the 162.0 × 77.3 × 8.0 mm phone spec with 0.2 mm clearance. The open front leaves the screen clear, and the walls are 1.8 mm with a 1.5 mm back and a 1.2 mm lip that catches the screen edge. Camera cutout on the back Button slot along one side Bottom slot for USB-C and the speaker Prints back-down with no supports One piece, no assembly The case is rigid, so the phone presses in from one corner. PLA works, but a flexible filament such as TPU is easier on the phone and less likely to crack the lip. The camera and button positions are estimates, so check them against your phone before printing the whole case.

4 hours agoRemix →

ReplixHD Gaming Cable Holder.

A low, slate-like desk plate in the spirit of a game-console accessory, with three rounded C-shaped clips standing in a symmetrical row. Cables press in from above, sit in a 4.4 mm round channel, and are held by smooth lips. Size: 60 × 20 mm, 5 mm base, 7 mm total height. Clips: three, 17 mm apart, 3.6 mm entry opening, lips about 1.2 mm thick at the opening. Floor: about 1.8 mm of material under each channel, measured from the tape recess. Underside: 48 × 12 mm tape recess, 0.5 mm deep. Printing: one solid piece, flat bottom, no supports needed.