Closed-Sleeve Glasses Ear Hooks
Created today
Description
Straight diagonal ear hooks with a closed, slip-on sleeve design. They act as anchors behind the ear to keep frames from sliding down when looking forward or down.
Adjustments for a perfect fit
- The internal sleeve: Currently set at 2.5mm width and 5.0mm height. This works for most standard wire or thin acetate frames. Thicker plastic frames will need these bumped up.
- The drop angle: The rear sphere is dropped back and down to catch the ear. You can tweak the position of the tail end to hug a specific ear shape tighter.
- Material choice: TPU or another flexible filament works best here for grip and comfort, though PLA will work if the friction fit is precise.
Images
More like this
Explore more in Keychains & EDC →
Football Keycap Topper
A custom Cherry MX-compatible mechanical keycap featuring a gently domed top and recessed seams, channeling the look of a classic basketball. Built from the ground up to respect a precise 17.25mm footprint, it trades the standard typing dish for a smooth, tactile convex surface. Court-Ready Specs Switch Profile: Deep Cherry MX compatible stem with a flared entrance for an easy press-fit. Surface Feel: A smooth domed top intersected by 0.6mm-deep recessed channels tracing the iconic hoops cross-and-arc pattern. Dimensions: Exact 17.246 mm square footprint at the base, tapering cleanly up to the rim. Printability: Designed fully manifold with built-in internal bracing ribs. The bottom cross interface is lightly chamfered to combat elephant's foot and ensure tight tolerances straight off the bed.
M22 Threaded Kettlebell Stash
A two-piece threaded kettlebell stash keychain. The main body has been hollowed out to maximize internal storage, then split squarely at the equator with a sturdy 2mm-pitch thread holding the halves together. Both halves print exactly as oriented — the base sits flat on its machined underside, and the top half prints directly on its equator ring. Fitment Notes Thread Clearance: Engineered with a 0.5mm radial offset on the internal thread. Check your flow rate if the halves bind on the first turn. Split Ring: The arch remains standardized for a 1.5mm wire gauge ring. Internal Volume: The cavity is approximately 20mm wide and 19mm deep when closed. Fits standard folded emergency bills or small hardware.
CourtGuard — Vented Finger Splints
Designed to quickly immobilise jammed or sprained fingers, CourtGuard splints provide rigid support without trapping moisture. Ideal for handling the inevitable basketball court impacts, the half-cylinder trough design features a rounded capsule geometry that sits comfortably against the skin without digging in. A dorsal ridge of vent holes keeps the finger cool during recovery, while integrated side notches securely anchor standard Velcro straps to keep the splint exactly where it belongs. Sizes Included Small (Pinky): 55mm length, 15mm inner diameter, 4 vent holes. Medium: 65mm length, 18mm inner diameter, 5 vent holes. Large: 75mm length, 21mm inner diameter, 6 vent holes. Print Notes All three sizes are designed to print-in-place in their current flat orientation, requiring absolutely no supports. A rigid material like PETG or standard PLA is recommended for maximum immobilization.
Mechanical 40-Quarter Dispenser
A fully mechanical, gravity-fed coin magazine tailored for standard U.S. quarters. Designed to slip into a pool cue bag, it stores a full $10 roll vertically and cleanly dispenses exactly $1 (four quarters) per cycle into the palm of the hand. The mechanism relies on a two-stage sliding escapement. In the resting position, the bottom four coins sit perfectly flush inside the 7.2mm-thick slider pocket. When the thumb tab is pulled outward, a chamfered ramp on the top trailing edge of the pocket catches the fifth quarter and guides it smoothly onto the solid tail of the slider, suspending the rest of the stack. Once the pocket aligns with the drop chute at full extension, the isolated four quarters fall through. A captive printed pin mounted from the base runs in an internal track on the slider, acting as a hard travel limit for both the pull and return strokes. Design Features Threaded Cap: The top of the magazine tube features a coarse 4mm-pitch thread, securing the cap firmly for travel. Clearance-Tested Slot: The stopper pin track is positioned well behind the coin pocket to ensure no interference with the resting quarters. Coin Bore: Sized at 25.2mm to allow smooth gravity feed for a 24.26mm quarter. Slider Geometry: The 7.2mm thickness dictates the exact four-coin dispense count.
Aegis — Symmetrical Barrel Plaque
A precisely dimensioned rectangular charm featuring gently rounded edges and delicate engraved details. Designed to lie perfectly flat while capturing intricate central motifs. Features Dimensions: 38.10 mm × 16.10 mm × 4.57 mm Top-to-Bottom Passage: A clean 3 mm cylindrical tunnel runs completely inside the narrow vertical profile. Surface Art: Features a recessed shield, twin vertical channels, and a soft continuous curved arc near the base.
60mm Print-In-Place Concentric Gyro
A four-ring concentric gimbal toy designed for fully assembled printing. The rings pivot independently on alternating axes using built-in conical hinges. All exterior edges are rounded for comfort. Clearances: 0.5 mm radial and axial gap between all moving surfaces. Overhangs: Conical pivots operate at a 45-degree angle, requiring no supports. Base: Rings are coplanar at z=0 to ensure solid bed adhesion. Dimensions: 60 mm outer diameter, 12 mm overall thickness.