Cutting Board Corner Grip Feet
Created today
Description
A set of four corner cups that slip over the corners of a cutting board and grip the counter, so the board stays put under a knife. Each foot is a 25 mm square cup, 8 mm tall, with a corner socket on top and a gently domed, nubbed underside.
The socket has 2.4 mm walls on the two outer sides and a 2.5 mm floor, so it is 5.5 mm deep. The two inboard sides are open, so the board corner slides in and the outer walls hold it. The underside rises about 1.2 mm toward the centre and carries 1 mm grip nubs on a 2 mm pitch.
Remix hooks
- Socket depth: the floor is 2.5 mm, which leaves 5.5 mm of grip. Thinner floor or taller cup means a deeper hold. Heavy or thick boards benefit most.
- Cup footprint: 25 mm is a choice, not a constraint. Go larger for more adhesive area or a wider stance.
- Wall thickness: 2.4 mm on the outer sides. Raise it for a stiffer clamp, lower it toward 1.6 mm for more flex.
- Nub size and pitch: 1 mm nubs at 2 mm spacing. Larger, sparser nubs give more bite on rough counters. Finer ones suit smooth laminate.
- Dome rise: 1.2 mm. Set it to 0 for a flat base with the same texture.
- Closed-corner variant: add walls on the inboard sides for a full pocket, with a slightly oversize opening for easy loading.
Notes for printing and pairing
- TPU is the sensible material, since PLA nubs will not grip much.
- A dab of adhesive in the socket helps on heavy boards.
- Pairs with non-slip shelf liner or rubber pads under the cup as a second grip layer.
- The 4 feet are laid out in a 2 by 2 grid with 6 mm gaps.
Images
More like this
Explore more in Kitchen & Bathroom →
Softflow — M22 Faucet Splash Diffuser
Softflow is a screw-on splash diffuser for faucets with an M22x1 male outlet thread. The base is perforated with a staggered hex grid of small holes, breaking the flow into many fine streams for a softer, wider spray. A short open chamber between the thread and the perforated floor lets water spread across the whole hole pattern before it exits. Features M22x1 female thread, 8 mm deep, with a beveled lead-in at the opening Staggered hex grid of 1.5 mm holes at 2.6 mm spacing, inside an 18 mm circle 3 mm perforated floor with a relief chamber above it Chamfered top and bottom edges on a round body Dimensions Outer diameter: 28 mm Overall height: 16 mm Thread: M22 x 1 mm pitch, 8 mm engagement depth Floor thickness: 3 mm Print notes Print with the perforated face down on the bed, opening facing up; no supports are needed. Thread fit has not been tested against a real faucet. If it binds, increase the thread clearance slightly. A fine layer height (0.12–0.16 mm) keeps the small holes and thread crisp. PETG or ASA suits wet, warm-water use better than PLA.
Square-Base Bowl That Stays Put
A bowl that skids across the counter or tips the moment you stir it is the annoyance; this one has an almost square base that keeps it planted. The base is a 70 mm square with rounded corners, so it sits flat instead of rocking, and the walls flare out to a 120 mm rim that is rounder and easier to eat from. What decides the fit Base footprint: 70 mm rounded square — the number to check against your shelf, tray or cupboard. Rim: 120 mm across at the widest point. Height: 50.8 mm (2 in). Walls and floor: 3 mm thick, so it holds its shape without being heavy. It prints as one piece, standing on its flat base, so no supports are needed and the inside comes out clean.
Bag Holder Stand with Spring Clamp Ring
A freestanding stand that holds a freezer or piping bag open so both hands are free for filling. The bag mouth is pulled through a 120 mm inside-diameter ring, folded over the outside, and secured with a separate split clip that grips the folded rim all the way round. The base is a wide 270 × 250 mm plate with a rear post, so the stand resists tipping when a bag is loaded. The ring sits at the top of the post, 165 mm above the plate, with a flared lip to keep the fold from slipping off. Ring: 120 mm inside diameter, 40 mm tall, on a short arm off the post Base: 270 × 250 mm, 8 mm thick, chamfered edges, with a gusset on the post Clip: split spring ring, 24 mm tall, with finger tabs for opening Parts: base with post, ring, and clip are colour-labelled; the clip prints separately Material: PETG suggested for the clip so it keeps its spring To use, pull the bag mouth up through the ring, fold it down over the outside, then snap the clip over the fold. The ring height suits bags up to roughly 165 mm long; longer bags will rest on the base. The clip's grip has not been test-printed, so the gap may need adjusting for thicker or thinner bag film.
Leanto — Sawtooth Taco Rack
Leanto is a minimal plate-top rack that holds three hard taco shells upright at a 45° slant, one behind the other. The profile is a true sawtooth: each slanted surface ends in a vertical wall that also stops the next shell, with no solid base underneath. Features Three 45° ramps, 48 mm pitch, 48 mm tall vertical backs Open underside, 3 mm shell walls One forward-leaning stop at the front to hold the first shell Two thin side runners tie the teeth together Dimensions About 100 mm wide and 150 mm front to back Fits on a standard dinner plate
Square Bioplastic Tile Mold with Corner Pins
What it's for A square casting mold for thin, translucent starch-based bioplastic tiles. Four pins inside the cavity leave a hole in each corner of the cast tile, so neighbouring tiles can be tied together with fishing line into a stained-glass-style hanging grid. Dimensions Cavity: 120 × 120 mm, 2 mm radius inside corners Outer size: 124 × 124 mm, total height 6.2 mm Walls: 2 mm thick, 5 mm above the floor Floor: 1.2 mm, continuous and flat underneath Pins: 4 mm diameter, 4 mm tall above the floor, centred 8 mm from both adjacent inner walls, clear of the walls Print notes One solid piece, no supports, flat underside Pins are fused into the floor Low filament use thanks to the thin floor and walls Remix ideas Change the pin spacing for larger or smaller holes Add mid-edge pins for extra connection points Scale the cavity for rectangular or smaller tiles
Toy Story Sky Cloud Cookie Cutter
A cookie cutter echoing the wallpaper clouds from Andy's room: a big bump on the upper left, smaller puffs along the top and a long flat base. The centre is open so dough passes straight through. 15 mm tall wall, about 1.2 mm thick, thin clean cutting edge on the flat bottom Widened rim at the top for pressing by hand About 100 mm wide, prints flat with no supports