Drawerling — 115 x 150 Desk Drawer Bin
Created today
Description
Drawerling is an open-top rectangular bin sized for a desk drawer, built to exact external dimensions of 115 × 150 × 60 mm. Straight walls, a solid floor and softly rounded vertical corners make it easy to wipe clean and print without supports.
Dimensions
- External: 115 mm wide × 150 mm deep × 60 mm high
- Walls: 2 mm
- Floor: 2 mm, solid
- Corner radius: 4 mm (vertical edges)
Features
- Fully open top, no lid, hinges or handles
- Flat base for support-free FDM printing
- Single watertight body, STL-ready
Photos
Technical views
More like this
Explore more in Storage & Organization →
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.
Drawer Sleeve Box With Mounting Pad
Open-top rectangular sleeve, 86 x 52 x 127 mm, for a sliding drawer. Smooth interior, 1.6 mm floor, sides and front, 2.4 mm back wall. A raised 40 x 40 x 3 mm pad on the back carries two M3 nut traps. Remix hooks Pad position: top edge sits 10 mm below the rim; pad is centered in X. Move or resize freely. Nut traps: 5.7 mm hex, 2.5 mm deep, 25 mm apart, with 3.4 mm blind holes behind them. Blind holes stop 0.8 mm short of the inside; thicken the back wall to go deeper. Edges: 3 mm vertical rounding, 6 mm 45° bottom chamfer (prints without supports). Drains: two 3 mm holes at X = ±20 mm. Pairs with a matching drawer 3 to 4 mm smaller in each direction.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Offenes Schreibtischregal mit Rampe
Schreibtische müllen immer von der Mitte her zu. Dieses Regal hebt den Kleinkram aus dem Weg und teilt die Fläche in der Mitte mit einer harten Rampe – links liegt das Fach tief für flaches Zeug, rechts hoch, damit darunter noch Platz für größeres Zubehör bleibt. Alles bleibt zugänglich und nichts verhakt sich. Eckdaten Spannweite: 450 mm Standfläche (Tiefe): 180 mm Höhe: 250 mm Druck: Wird flach auf der Rückseite liegend gedruckt und kommt komplett ohne Stützstrukturen aus.
4-Compartment Kitchen Organizer
A small, straightforward drawer organizer divided into four compartments. One wide compartment runs the length of the tray for standard utensils, while the back half is split into three smaller bays for loose items. Dimensions Overall size: 150 mm long × 100 mm wide × 35 mm tall Wall thickness: 2 mm solid walls and dividers Long bay: ~146 mm × 47 mm (ideal for small spoons or forks) Small bays: ~47 mm × 47 mm each Print notes Designed to print flat on its base without supports. Generous corner radii keep things from getting stuck in the corners. PLA or PETG both work fine for drawer use.