Eukalyptuskranz für 21-mm LED-Stabkerzen
Created today
Description
Adventskranz-Grundform mit dichtem Eukalyptuslaub und vier integrierten Kerzenhaltern für LED-Stabkerzen mit 21 mm Durchmesser.
Passung
- Kerzenbohrung: 22,6 mm Durchmesser, 20 mm tief, mit Einlauffase – passend für 21-mm-Stabkerzen.
- Vier Halter im Abstand von 90°.
- Kranz ca. 200 mm Außendurchmesser, ca. 45–50 mm hoch.
Vor dem Druck prüfen
Den tatsächlichen Kerzendurchmesser nachmessen; bei Kerzen über 22 mm sitzt die Bohrung zu knapp.
Druck
Blätter sind unter ca. 40–48° nach oben geneigt, der Ring hat eine ebene Unterseite – Druck ohne Stützen. Passt nicht für Kerzen mit Durchmesser unter ca. 20 mm (sie stehen locker).
Images
More like this
Explore more in Decor & Display →
Christmas Tree Lantern for LED Tealight
A Christmas tree lantern that sits over a battery LED tealight, so the light stays hidden inside instead of glaring from a bare tealight on the table. The walls are perforated with rings of small round holes that throw dots of light, and the bottom is open so the LED can be placed or swapped without taking anything apart. Key numbers Height: about 135 mm including star Base diameter: 90 mm, open underneath (inner opening about 87 mm) Wall: 1.6 mm, three stacked tiers Perforations: 4.2 mm holes, staggered rings Star: separate colour, peg-mounted into the top tier Printing Print upright, open end down, no supports needed for the cone walls Green for the tree, gold or yellow for the star Use a 0.4 mm nozzle; a lighter or translucent filament glows more
Christmas Tree Lantern with LED Holder
What it's for A Christmas tree lantern with perforated walls that hides a 38 mm battery LED light. A removable twist-lock tray inside the base holds the light, so it stays in the tree when the tree is carried or moved. Dimensions Base diameter: 90 mm, open underneath Total height: about 140 mm including the star Wall thickness: 1.6 mm Light ring: 39.4 mm inside diameter, 6 mm tall Tray: 66 mm disc with three locking lugs Assembly Line the tray lugs up with the gaps between the three tabs inside the wall. Push the tray up past the tabs, turn it about 60°, and lower it onto the tabs. Place the light in the ring. Remix ideas Make the ring taller for a deeper hold. Add a thumb notch to the tray for easier twisting. Change the hole pattern for different light dots.
Ripple Dune Twist-Lock Lamp
A soft, dune-rippled shade sits on a rounded pedestal base, like a small sand-sculpture lamp. The two pieces lock together with a printed twist-lock joint, so no hardware is needed. A bulb holder pocket sits inside the shade, and the cable runs through the base. Design notes Three lugs on the base neck drop into slots in the shade, then a short twist locks them. The cable hole enters the rear of the base and rises through the neck into the bulb pocket. The 24 mm pocket suits a small E14-style lamp holder. Use a low-heat LED bulb. Prints as two parts, base flat on the bed and shade open end down.
Moonlit Ghost Chain Swing Display
A friendly sheet-wearing ghost sits on a chain swing hanging from the horn of a crescent moon, in the spirit of a Halloween nursery rhyme. His blue tennis shoes dangle below the sheet and his hands grip the chains above his head, the way a kid holds on mid-swing. Crescent moon with shallow craters Chain swing with a rounded seat Cut-out eyes and a recessed smile Flat rounded base keeps the whole scene standing upright Sand the edges before handing it to a child.
Moldura A4 Vertical 250 × 337 mm, Fundo Aberto
Moldura para folha A4 (210 × 297 mm) na vertical, em duas metades unidas por pinos-guia, com a folha entrando por uma fresta na travessa superior. Medidas Externo: 250 × 337 × 15 mm Abertura visível: 202 × 289 mm, lábio frontal de 5 mm Bolso do papel: 212 × 299 mm Fresta superior: 206 mm de largura Fixação e encaixes 4 pinos-guia de Ø5 × 8 mm na metade superior, com alojamentos de Ø5,6 mm na inferior Keyhole para prego: entrada de Ø10 mm e fenda de 4,2 mm, na travessa traseira superior Gancho na borda inferior frontal Verifique antes de imprimir Cada metade mede 250 mm de largura, acima dos 220 mm de uma impressora comum. A traseira é aberta abaixo da travessa do keyhole, então nada segura a folha por trás. Não serve para papel muito fino ou ondulado.
Engraved Name Block with Ogee Edges
A solid 4 x 3.5 x 1 in block with "Francisco Suarez" indented into the 4 x 1 in front face. All edges carry a Roman ogee profile: a concave sweep flowing into a convex bead. Size: 101.6 x 88.9 x 25.4 mm Name indented 1.5 mm, centered on the front face Smooth S-curve edge profile on all twelve edges Flat base, prints without supports