Made by a Guest
Created today
Description
A 1U, 19-inch rack mount for four Orange Pi 5 Pro boards. The front panel fills a standard rack opening, while the rear tray carries the boards side by side at 105 mm spacing. Slotted ear holes line up with standard rack spacing, and four 66 × 16 mm cutouts in the panel sit in front of each board for power and Ethernet cables.
Each board position has four standoffs with 2.2 mm pilot holes. Check the standoff pattern and the cable-side cutouts against your boards before printing.
Photos
Technical views
A compact stacked rack that holds four 2.5" SSDs, each sliding into its own open-front slot. Side windows and diamond-shaped rear vents keep air moving and leave room for cables. Remix hooks Slot height (sw, 10.5 mm): sized for 7 mm drives with margin; raise to ~12 for 9.5 mm drives. Bay count (n, 4): change it and the body height follows. Slot width (76 mm) and depth (100 mm): tuned for 69.85 x 100.5 mm drives; adjust for other trays. Vent shape: swap the diamond rear vents for round ones or a slot pattern. Feet: the two rails (3 mm tall) can be removed, widened, or swapped for screw tabs. Pairs with: a SATA hub, or a second rack stacked side by side.

What it's for A protective case for the iPhone 17 Pro Max in light blue, with a raised rose on the back below the camera cutout. Dimensions Phone body: 163.4 × 78 × 8.75 mm, with 0.3 mm of play per side Walls 4 mm, back 3 mm Rose relief: 1 mm, flat-topped layers Remix ideas Recolour the rose in blue tones to blend with the case Make the rose taller or soften its edges Swap the rose for another motif
A Flex Mini 2.5G that sits loose in an under-desk bracket slides out the open end the first time someone bumps a cable. This mount screws to the desk underside and closes that end with a slide-in cover. Pocket: 110 × 72 × 28.5 mm, 5 mm bottom lips, wide port window in the front wall, cable slot in the -X end. Cover: 2.8 mm plate slides up into a 3.2 mm slot at the +X end. Four small bumps hold it by friction. Mounting: two countersunk screw ears on the top plate. Print: mount with the top plate face down; cover flat as laid out. No supports needed for the cover. Check the pocket size against your unit before printing.
What it's for A solid-walled enclosure for hiding and cooling equipment. Every side wall is closed, and the only airflow path is a sturdy grid cut into the floor, so the box stays dark and quiet from the sides. A 30 × 20 mm cable hole in the lower rear corner lets wiring in and out, and the flat lid lifts off for access. The model prints as separate pieces: the box, the lid and four feet. The lid is a flat plate with a locating lip underneath, slightly larger than the box on every side so it overhangs and can never drop inside. Each foot carries its own coarse threaded stud, so the feet screw directly into matching threaded holes in the floor bosses with no separate fasteners. Dimensions Box: 290 × 200 × 130 mm, with 4 mm walls, solid on all four sides, an 8 mm floor, and a 50 mm solid border around the floor grid. The floor grid is centred on the narrower floor. The thicker floor makes the mesh bars deeper, so airflow per opening drops slightly. Inside fillets: 10 mm radius on the vertical corners and the floor-to-wall edges, stopping 15 mm below the rim. The top 15 mm stays square so the lid and its lip fit without changes. Lid: 294 × 204 mm, 9 mm overall with a 5 mm plate and underside lip; overhangs the box by 2 mm on all sides; 140 mm fan opening and four 3 mm fan screw holes at 124.5 mm center-to-center. Cable hole: 30 × 20 mm in the rear wall, set 20 mm from the left edge and 12 mm above the bottom, inside the solid section so it doesn't weaken the corners. Feet: four solid 24 mm discs, 10 mm tall, each with a 6 mm thick, 8 mm long threaded stud on top; 18 mm overall. The studs use a 1.5 mm pitch. Foot sockets: four corner bosses widened to 14 mm, with threaded holes 6.6 mm across and 11 mm deep at the same 1.5 mm pitch, giving about 0.6 mm clearance on diameter. Print notes Print the box, lid and feet separately. Print the lid lip-side up so its flat face sits on the bed and the lip rises clear of the plate. The floor grid benefits from enough perimeters to keep the bars sturdy. The threads have not been test-fitted; if the feet bind, raise the socket diameter slightly, and if they wobble, lower it. Test-fit the fan and check its screw-hole spacing before committing to a full print. Remix ideas Add a removable filter frame behind the fan opening. Add internal standoffs or a shallow tray for mounting equipment inside. Resize or duplicate the rear cable port for thicker cable bundles. Swap the floor grid for a denser or more open pattern to change the airflow.
Schlichtes Gehäuse für das 7-Zoll-Display Pollin LS-7T, im Stil eines kleinen Werkstatt-Terminals. Hinten sitzt eine abnehmbare Rückwand mit Lüftungsschlitzen. Der U-förmige Standfuß ist ein eigenes Bauteil und liegt zum Drucken flach neben dem Gehäuse. Hinweise Standfuß separat gedruckt, ohne Stützen druckbar Befestigung am Gelenk mit je einer M5-Schraube samt Mutter Kabelschlitz über die volle Breite, 10 mm hoch Platinen-Abstandshalter im Raster 122 × 79 mm (bitte gegen die Platine prüfen)
A vertical stand that docks two closed laptops side by side on their edges, freeing up desk space. Built for a setup with a work laptop and a personal laptop sharing one desk. Each slot has a window cut through its walls, so a hand can rest on a lid to check for heat without removing the laptop. What it's for Holding two closed laptops upright, one per slot, with a solid 15 mm divider between them. Checking temperature by touch through the window in each slot wall. Staying put thanks to a wide, weighted base that resists tipping. Dimensions Slot width: 20 mm each Divider between slots: 15 mm Outer and divider wall thickness: 4 mm (the divider is the 15 mm gap) Overall width: about 93 mm Overall depth: 270 mm base, 250 mm walls Overall height: about 82 mm (12 mm base plus 70 mm walls) Windows: 110 mm long by 35 mm tall, with rounded ends, through each wall Weight pockets: four underneath, each 14 × 80 × 7 mm Print notes Print with the base flat on the bed. No supports are needed for the main body. The underside pockets open downward. Fill them with steel washers, shot or similar, then seal them with felt, a sticker or a thin plate. Use PETG or PLA with 3 or more perimeters for stiff walls. Remix ideas Change the slot width to fit thicker laptops or ones in sleeves. Add a third slot for a tablet. Add rubber feet or a felt pad under the base. Add a cable cutout in the base for charging leads.