Halloween Spider Decoration for Shelves
Created today
Description
A Halloween spider decoration that stays put on a shelf or mantel, instead of a flat cutout that falls over. Eight bent legs spread out as a stable base.
Key numbers
- Body: about 24 mm abdomen, 14 mm head
- Leg span: roughly 80 mm across
- Print: no brim needed; supports under the legs and head may help
- Material: any PLA works; multicolour optional
Photos
Technical views
More like this
Explore more in Decor & Display →
Tannenbaum — Adventskalender mit Steckdeckeln
Tannenbaum-Adventskalender mit 24 Fächern, erhabenen Zahlen 1–24 und Steckdeckeln mit Griffknopf. Der Baum hängt in der Ansicht an einer roten Wand mit Lichterkette, Kugeln, Schnee und Stern. Features 24 Fächer in Reihen 1–6 plus Stamm mit 3 Fächern Deckel mit Griffknopf und Steckzapfen, per Reibung gehalten Schlüssellöcher auf der Rückseite zum Aufhängen part = "scene" zeigt die Wanddekoration, nur zur Ansicht Print notes Zum Drucken part auf row1 bis row7 oder doors stellen Die Wanddekoration gehört nicht zum Druckteil
Bat Silhouette Disc, 20 mm
A 20 mm round disc, 2 mm thick, with a bat silhouette cut clean through it: spread wings, pointed ears and a small tail, the cutout now spanning roughly 17 mm of the disc's width. The outer rim is lightly chamfered, and the thin wing tips are the narrowest parts of the cut, so they are the first place to look when checking a print. Remix hooks Diameter — 20 mm. This is a choice, not a constraint. Take it up to coin or badge size and the bat gets more room to read; shrink it much below 20 mm and the wing tips start to crowd. Thickness — 2 mm. Thin enough to stay light, thick enough to hold together across the wing tips. Going thinner is where the tips become risky; going thicker makes it a chunkier pendant or token. Bat scale — about 17 mm across. This is the tight setting: the wing tips sit roughly 1 mm from the disc edge, so scaling the cutout up any further breaks through the rim. If you want a bigger bat, thin the rim first or narrow the wingspan slightly — scaling the cutout down instead gives a heavier border and a more solid-looking disc. Outline. The chamfer on the outer edge is cosmetic — swap it for a flat rim, a rounded edge, or a ring of small holes if you want a different border treatment. Pairs with A hole through the rim turns it into a hanging piece; a flat back makes it easy to stick onto a card, a lid or a magnet. Two mirrored copies back to back give a double-sided version, and the same cutout logic works on any flat blank — a square tag, a hex token, an oval. Treat it as a silhouette template rather than a finished object: any winged shape dropped into a disc of these proportions will read the same way, as long as you watch the rim margin.
Funfair Swing Ride with Crank, 100 mm Base
Funfair swing ride with a hand crank on top. Turning the crank spins the canopy and seat ring around a fixed central pin, and each of the six seats hangs from a captive ball joint so it swings outward as the ride turns. Base: 100 x 100 x 6 mm plate with a 30 mm column and 14 mm mast Spinning top: 70 mm seat ring and cone canopy on a 8 mm pin, 0.3 mm bearing clearance Seats: six, each on a 7 mm captive ball with a 3 mm rod, printed in place Crank: 30 mm arm with a 7 mm handle on top of the canopy Print in place, no supports needed for the base; the ring cavities bridge over the balls Overall height about 112 mm
OO Scale Arched Door Frame 13x26mm
Arched door frame and separate door for an OO scale (1:76) house, sized for a 13 x 26 mm wall opening with a semicircular top. The frame is 2 mm deep and continues around the inside of the arch, leaving a semicircular glass gap above the door. Frame: 12.8 mm wide, 25.9 mm tall, 2 mm deep Glass gap: semicircle, 8.8 mm across Door: 8.4 x 17.8 mm, printed as a separate piece Door detail: four raised panels, round handle, letterbox plate Fit: 0.1 mm clearance per side in the wall opening Print with a fine layer height; panel relief is 0.4 mm
Deutschland — Relief Map with City Pins
Deutschland to a relief map of Germany with raised uplands and mountains, carved river channels, and 12 major cities marked by slim pins. Each pin has a round base, a ball head and a small flag plate with the city name in raised letters, readable from above. Features Terrain relief in smooth stepped layers, with Alps and central uplands Four carved rivers 12 labelled cities: Berlin, Hamburg, Monachium, Kolonia, Frankfurt, Drezno, Brema, Hanower, Stuttgart, Norymberga, Dusseldorf, Lipsk Three colour regions: map, pins, name flags Print notes Pins are thin (1.8 mm), so print slowly or glue them in if they snap Outline and city positions are simplified, not cartographic
Chubby Baby Dragon Figurine
A cute chubby yellow baby dragon with a big round head, cream oval belly, green eyes, short limbs, a tiny tail and small horns. About 80 mm tall with a flat base, built as one welded body. Remix hooks Head size: the head is a 48 mm sphere; enlarge it for a more chibi look, but keep the body wide enough to support it. Eyes: 10 mm ovals; push them outward or scale them up for a different expression. Belly: a flattened ellipsoid at the front; swap its colour for multi-colour printing. Pairs with: a round display plinth, or a keychain loop on the horns. Limbs and tail: short ellipsoids, easy to lengthen if you want a more dynamic pose.